Mountfield 2L0536043/MC, Руководство по эксплуатации

Страница: 20 / 36

EN - 5
1. Start the machine
(par. 6.3).
2. Operate the drive
lever.
3. Disengage the drive
lever.
2. The wheels should
move the machine
forward.
3. The wheels should
stop and the machine
stops moving forward.
Test driving No abnormal vibrations.
No abnormal sound.
If any of the results fail to match the indications
provided in the tables, do not use the machine! Con -
tact a Authorised Mountfield Service Dealer to have it
checked and repaired if necessary.
6.3 START-UP
NOTE Start up the machine on a flat surface without
obstacles or high grass.
6.3.1 Models with manual start handgrip
(Fig.17.A/B)
NOTE The engine brake lever must be kept pulled to
prevent the engine stopping.
6.3.2 Models with push-button electric start
command (Fig.18.A/B/C/D/E)
Insert the supplied battery in the relative engine
compartment ( Fig.18.A); (follow the instructions provided
in the engine manual).
An engine with non-removable built-in battery is included
on some models ( Fig.18.B ).
NOTE The engine brake lever must be kept pulled to
prevent the engine stop.
6.4 OPERATION
IMPORTANT When working, always keep a safe
distance from the cutting blade, given by the length of the
handle.
6.4.1 Grass cutting
1. Start moving forward and mowing the grass area.
2. Adjust the speed and cutting height (par. 5.5) in relation
to lawn conditions (grass height, density and humidity)
and the amount of grass to be cut.
3. It is recommended to always cut at the same height
and in two directions (Fig.20).
For mulching or rear grass discharge:
• Never cut more than one third of the total grass height
per single pass (Fig.19).
• Keep the chassis clean (par. 7.4.2).
For side discharge: avoid discharging the cut grass
from the side of the lawn yet to be mown.
6.4.2 Grass catcher emptying
For grass catcher with bag full warning indicator:
Lifted = empty. Lowered = full*.
shows when the grass catcher is full
and need to be emptied.
To remove and empty the grass catcher:
1. Wait until the cutting blade stops (Fig.21.A);
2. Remove the grass catcher (Fig.21.B/C/D).
6.5 STOP (Fig.22.A)
After having stopped the machine, it will take a few
seconds for the cutting blade to stop.
Do not touch the engine after stopping it. Risk of
burns.
IMPORTANT Always stop the machine.
• When moving between work areas.
• When driving on grass free surfaces.
• Close to an obstacle.
• Before adjusting the cutting height.
• Any time the grass catcher is removed or refitted.
• Any time the side discharge chute (if available) is
removed or refitted.
6.6 AFTER USE (Fig.23.A/B/C/D)
1. Clean (par. 7.4).
2. If necessary, replace damaged components and
tighten any slack screws and bolts.
IMPORTANT Any time the machine is inactive or
unattended:
• Remove the spark plug cap (for models with manual start
handgrip)(Fig.23.B/C).
• Press the tab and remove the safety key (for models with
push-button electric start) (Fig.23.D).
7. MAINTENANCE
7.1 GENERAL INFORMATION
The safety regulations to follow are described in
chap. 2. Comply with these instructions to avoid serious
risks or hazards:
Before commencing any inspections, cleaning or
maintenance/adjustments on the machine:
• Stop the machine.
• Make sure that any moving component has stopped.
• Wait until the engine cools down.
• Remove the spark plug cap (Fig. 23.B).
• Remove the key (Fig.23.D) (for models with
push-button electric start).
• Read the relevant instructions.
• Use suitable clothing, protective gloves and
goggles.
7.2 ROUTINE MAINTENANCE
• The frequency and types of maintenance are summarised
in the "Maintenance Table" (chapter 10).
IMPORTANT Any maintenance and adjustment
operations not described in this manual must be carried out
by a Authorised Mountfield Service Dealer.
7.2.1 Refuelling
Place the machine in a stable horizontal position on the
ground.