Mountfield 2L0536033/MC, Руководство по эксплуатации

Страница: 21 / 36

EN - 6
7.2 ROUTINE MAINTENANCE
• The frequency and types of maintenance are summarised
in the "Maintenance Table" (chapter 10).
IMPORTANT Any maintenance and adjustment
operations not described in this manual must be carried out
by a Authorised Mountfield Service Dealer.
7.2.1 Refuelling
Place the machine in a stable horizontal position on the
ground.
Refuelling must be performed with the machine
stopped and with the spark plug cap removed.
Refuel according to the methods and cautionary measures
indicated in the owner's manual of the engine.
Machines with vertical storage possibility (chap.
8.1) have a tank that contains a fuel level indicator. Do
not fill the tank above this level indicator (Fig.24.A).
IMPORTANT Clean any trace of leaked fuel. The
warranty does not cover damages caused by the fuel to
plastic parts.
NOTE Fuel is perishable and should not remain in the
tank for more than 30 days.
7.2.2 Check/top-up engine oil
Check/top-up the engine oil according to the methods and
cautionary measures indicated in the engine manual.
For the correct operation of the machine, regularly replace
the engine oil, according to the instructions in the engine
manual.
Make sure to have restored the oil level before using the
machine again.
7.3 OCCASIONAL MAINTENANCE
7.3.1 Cutting blade
All operations concerning cutting blade
(disassembly, sharpening, balancing, repair, reassembly
and / or replacement) must be performed by an
Authorised Mountfield Service Dealer.
Make sure damaged, misshapen or worn cutting
blade are replaced, together with the securing screws to
preserve balance.
IMPORTANT Always use original cutting blade bearing the
code indicated in the “Technical Data” table.
7.4 CLEANING
Clean thoroughly following the instructions below every
time it is used.
7.4.1 Cleaning the machine
• Always make sure the air intakes are free of debris.
• Do not use aggressive liquids to clean the chassis.
• To reduce the risk of fire, keep the engine free of grass,
leaves residues or excessive grease.
• Wash the machine with water after each use.
7.4.2 Cleaning the cutting blade assembly
• Remove grass debris and mud accumulated inside the
chassis.
Models without washing connection
• To access the lower part, tilt the machine from the side
indicated in the engine's manual, following the relative
instructions, making sure that the machine is stable
before carrying out any intervention.
For side discharge: remove the discharge chute (if
mounted - par. 6.1.2d.).
To wash the internal part of the cutting blade assembly,
proceed as follows (Fig.25.A/B/C):
1. Always stay behind the handle of the lawn mower;
2. Start the engine.
If the painting of the internal side of the chassis comes
off, take immediate action, by retouching the painting with
anti-rust paint.
7.4.3 Cleaning the grass catcher ( Fig.26.A/B)
Clean the grass catcher and leave it to dry.
7.5 BATTERY
The battery is supplied for the models with push-button
electric start. For instructions regarding the battery
life, recharging, storage and maintenance, follow the
instructions in the instructions manual of the engine.
8. STORAGE
When the machine is to be stored away:
1. Start the engine outdoors and leave it running at idle
until it stops in order to consume all the fuel left in the
carburettor;
2. Clean the machine thoroughly (par. 7.4);
3. Check the integrity of the machine;
4. Store the machine:
• in a dry place;
• protected from inclement weather;
• in a place out of children's reach;
• making sure that keys or tools used for maintenance
are removed.
9. HANDLING AND TRANSPORTATION
Whenever the machine is to be handled, raised, transported
or tilted you must:
• Stop the machine (par.6.5) until the moving parts come to a
complete stop.
• Remove the spark plug cap (Fig.23.B) or remove the key
(Fig.23.D) or the battery (for models with push-button
electric start command).
• Wear heavy work gloves.
• Hold the machine in the points offering a safe grip, taking
into account the weight and its division.
• Use an appropriate number of people for the weight of the
machine and the characteristics of the vehicle or the place
where it must be placed or collected.
• Make sure that machine movements do not cause damage
or injuries.
When transporting the machine on a vehicle or trailer, always:
• Use an access ramp of suitable strength, width and length.
• Load the machine with the motor switched off and pushed by
an adequate number of people.
• Lower the cutting blade assembly (par 5.5).
• Position it so that it cannot cause a hazard for anybody.
• Fasten firmly to the device of transport using ropes or chains
to prevent it from tipping over causing damage and fuel
leaks.