![background image](http://html.mh-extra.com/html/moulinex/compacteo/compacteo_manual_1840043017.webp)
• To obtain the best results, we advise you to repeat this operation.
If your water is hard, increase the frequency.
In particular, do not use descaling agents for rinsing out the boiler, as they
could damage it.
A PROBLEM WITH YOUR GENERATOR ?
PROBLEMS
CAUSES
SOLUTIONS
The generator does
not come on and
the thermostat light
is not illuminated.
The appliance is not switched on.
Check that your appliance is correctly
plugged in
Water runs out of
the holes in the so-
leplate.
Water has condensed in the
pipes because you are using
steam for the first time or you have
not used it for some time.
Press on the steam control button away
from your ironing board until the iron
produces steam.
The soleplate is not hot enough.
Wait for the thermostat light to go out
before activating the steam button.
Your thermostat is faulty: the iron is
not hot enough.
Contact an Approved Service Centre.
11
Water runs out of
the holes in the
soleplate.
The boiler is too full.
Do not fill the boiler right up to
the top.
Water streaks
appear on the
linen.
Your ironing board is saturated with
water because it is not suitable for
use with a steam generator.
A mesh type ironing board must be
used to allow any excess steam to
escape.
Brown streaks
come through the
holes in the
soleplate and stain
the linen.
You are using chemical descaling
agents or additives in the water for
ironing.
Never add this type of product in the
water tank or in the boiler (see § “for
what water may be used”). Contact an
Approved Service Centre.
Your linen is not rinsed sufficiently
or you have ironed a new garment
before washing it.
Ensure linen is rinsed thoroughly to
remove any soap deposits or
chemicals on new garments which
may be sucked up by the iron.
The soleplate is
dirty or brown and
may stain the
linen.
You are ironing at too high a
temperature.
See our recommendations regarding
temperature control setting.
You are using starch.
Always spray starch on the reverse
side of the fabric to be ironed.
There is no steam
or there is little
steam.
The boiler is empty.
Fill the boiler.
The soleplate temperature is set to
the maximum.
The generator is working but steam is
very hot and dry As a consequence, it
is less visible.
The boiler is not yet ready.
After starting the appliance, wait for 6
minutes.
EN
1800121710-01 GM5010 GTL_110x154 04/01/11 09:06 Page11
Содержание compacteo
