background image

© 2014 Motorola Solutions, Inc. All Rights Reserved. 
 

 

 

 

 

 

 

 

 

 

                       

March 20, 2014 

       8073681 C

 

MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark 
Holdings, LLC and are used under license. All other trademarks are the property of their respective owners..

 

 

 

 

                                           RFID MODULE UHF CIRCULAR (FCC/IC) ENDCAP 
                                                     

RFID Regulatory information 

 
IMPORTANT NOTE FOR NORTH AMERICA: 

 
The RFID must not be used whilst the host WORKABOUTPRO4 is being powered by the ac/dc 
adaptor. 
 

FCC Information to Users: 

 

Radiation Exposure Compliance 
This product complies with the FCC RF exposure limits for an uncontrolled environment. For 
continued compliance, the product must not be held closer than 20 cm from the rest of the body.

 

This product must not be used in a holster or on a belt-clip.  
 
The host WORKABOUTPRO4 is configured to prevent WAN and RFID to be in co-transmission. The 
user cannot activate both at the same time. 
 

 
Federal Communication Commission Interference Statement. 
 
This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates uses and can radiate radio frequency energy and, if 
not installed and used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a particular 
installation.  
If this equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one of the following measures: 
  

•   Reorient or relocate the receiving antenna. 
•   Increase the separation between the equipment and receiver. 
•   Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected. 

•   Consult the dealer or an experienced radio/TV technician for help. 

  
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE 
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) 
THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY 
CAUSE UNDESIRED OPERATION. 
 
FCC Caution: Any changes or modifications not expressly approved by the party responsible for 
compliance could void the user's authority to operate this equipment. 
 
 
 

Содержание WA9903












Отзывы: