Motorola c18 Скачать руководство пользователя | Manualshive

Страница: 23 / 82

background image

98-08901C63-A

15

Hardware Description

3.1.2.3

Frequency Generation

There are three RF frequencies generated to enable frequency conversions within the radio:

• Front-end-down and Front-end-up Conversion LO Frequency:

The frequency plan is designed so that the Rx front-end-down

conversion LO and the Tx front-end-up conversion LO are the same frequency, which is generated in the dual synthesizer
IC. This LO is fed into the RFR3300 IC, where it drives the down-convert mixers and from where it is also redirected to the
RFT3100 IC, where it drives the single sideband up-convert front-end mixers. The basic synthesizer frequency is around
2 GHz, which supports the 1.9GHz band. The internal divide-by-two circuitry within the RFR3300 is able to produce
one-half the LO frequency to support the 800MHz band as well.

• The frequency required for the quadrature down-convert LO (translating the signal from IF to baseband) is generated from

the dual-synthesizer IC, as well as from an on-chip VCO in the IFR3300 IC.

• The quadrature up-convert LO (translating the signal from baseband to IF) is generated from an on-chip synthesizer on the

RFT3300 IC, as well as from an external VCO and loop filter circuitry.

All frequency generation uses a common 19.2MHz x-stall reference oscillator.

3.1.2.4

Baseband

This section describes power management, digital processing, memory and external interface requirements.

Figure 5 shows the baseband block diagram:

Figure 5. Baseband Block Diagram

INTERFACE

CONNECTOR

GENERAL PURPOSE ADC INPUTS

RUIM

FLASH

SRAM

SPARE

FLASH -

OPTIONAL

PM1000

HARNESS

1.8V VOLTAGE

REGULATOR

LCD INTERFACE

USB

TRANSCIEVER

UART1 INTERFACE

UART2/RUIM INTERFACE

PA_B+ (TO RF PA's)

PCM AND GPIO INTERFACE

ADDRESS AND DATA BUS

IGNITION

ON/OFF

VREG_MSMP

VREG_MEM_CORE

VREG_IF, VREG_RF_RX, VREG_RF_TX, VREG_SYNTH, VREG_TCXO

KEYPAD INTERFACE

SBI

RF CONTORLS

TRANSMIT I AND Q DATA

MSM5100

RECEIVE DATA

RF

BLOCK

VREG_MSMC

VREG_MSMA

VCC

AUDIO INTERFACE

«
...
21
22
23
24
25
...
»

Содержание c18



















































































Отзывы:

Нет отзывов

Похожие инструкции для c18

Бренд: Valor Страницы: 97

Бренд: BAFANG Страницы: 12

3T-MOTORS 3T45-20

Бренд: 3T-Components Страницы: 24

Бренд: Man Страницы: 132

MaxxForce DT 10

Бренд: Navistar Страницы: 109

EM-PMI540-T4000

Бренд: Danfoss Страницы: 71

EM-PMI540-T1500

Бренд: Danfoss Страницы: 76

Бренд: Perkins Страницы: 54

Бренд: Toro Страницы: 27

Бренд: YS Страницы: 4

Бренд: Yanmar Страницы: 222

Бренд: Honda Страницы: 15

Бренд: Honda Страницы: 60

Бренд: Stober Страницы: 34

Бренд: LONCIN Страницы: 219

Бренд: Barrus Страницы: 24

Бренд: WEN POWER Страницы: 28

Бренд: rojaflex Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды