Motorola c18 Скачать руководство пользователя страница 74

Страница: 74 / 82

Hardware Requirements for CDG2 and Field Testing

98-08901C63-A

C.3

c18 MODELS WITH A 28-PIN INTERFACE CONNECTOR

c18 models that have a 28-pin interface connector, may be supplied in two configurations:

• With hardware preset for RS232 communication mode
• Without hardware preset for RS232 communication mode
The second configuration enables communicating via USB.

Integrators should prepare test connectors or test points for the following pins:

For Configuration:

• AUDIO_IN: Must be pulled down with 10

Ω

to configure the c18 in USB+RS232 mode.

• USB_VBUS: Voltage (> 4 V) from the USB port must be present for configuring USB+RS232 mode (for configuration and

communication).

• OPT1: A 10k

Ω

pull-down resistor (R6203) on the c18 must be removed when using USB+RS232 mode. The location of the

R6203 resistor is shown in Figure 33. R6203 is not installed on c18 models that are not hardware configured for RS232
mode.

Figure 33. Location of the R6203 Resistor on the c18

Содержание c18



















































































Результаты поиска

Содержание c18

Отзывы:

Бренды по названию

Популярные бренды

Motorola c18, Руководство разработчика

Результаты поиска

Содержание c18

Отзывы:

Бренды по названию

Популярные бренды