Motorola c18 Скачать руководство пользователя | Manualshive

Страница: 26 / 82

background image

Hardware Description

18

98-08901C63-A

3.4

TURNING THE UNIT ON/OFF

This section describes the methods available to turn the c18 unit on and off.

3.4.1

On/Off Circuitry

The unit does not power-up automatically by connecting the power. There are two ways to turn on the c18 unit:

• Using the AUDIO_OUT_ONOFF pin
• Using the Ignition pin

It is recommended to use the AUDIO_OUT_ONOFF line to power-on or power-off the c18.

3.4.2

Turning the Unit On/Off Using the AUDIO_OUT_ONOFF Pin

The c18 module can be turned on or off using the AUDIO_OUT_ONOFF line (pin #53 on the 70-pin connector, pin #14 on the
36-pin ZIF connector and pin #17 on the 28-pin DIN connector). The AUDIO_OUT_ONOFF line has dual functions, as follows:

• It serves as an audio output.
• It serves as an on/off signal.
It is internally pulled high, to approximately VCC -0.6V.

To turn the modem on, the AUDIO_OUT_ONOFF signal should be pulled to GND through a 4.7K resistor for a minimum of
two seconds. The signal should then be released, and the module will begin the power-up sequence. During the next six to seven
seconds, the module does not communicate (for example, it does not respond to AT commands if configured for RS232
communication). For a detailed description of UART signals at power-up, see “UART1” on page 24.

To turn the module off, the AUDIO_OUT_ONOFF signal should be pulled to GND through a 4.7K resistor for a minimum of
two seconds. The signal should then be released. This initiates the power-down sequence, which includes deregistration from
the network. The process takes approximately three to eight seconds (typically five seconds). After the module has powered
down, the voltage supply can be disconnected from the module.

!

Caution

The module should not be turned off by removing the supply voltage. If the c18 is powered off by disconnecting the
power to the unit, the c18 module does not shut down properly and does not complete the deregistration procedure
from the network.

Note

When using this signal as audio output, make sure to decouple the load with a capacitor. Connecting a load directly
without the capacitor alters proper module functionality. For more details concerning the audio interface, see
“Hands-free Audio (Auxiliary Audio) Interface” on page 30.

!

Caution

The module should not be turned off by removing the supply voltage. If the c18 is powered off by disconnecting the
power to the unit, the c18 module does not shut down properly and does not complete the deregistration procedure
from the network.

«
...
24
25
26
27
28
...
»

Содержание c18



















































































Отзывы:

Нет отзывов

Похожие инструкции для c18

Бренд: Daspi Страницы: 40

Бренд: Eurotronic Страницы: 4

Бренд: Nice Страницы: 12

Бренд: Grundfos Страницы: 25

MerCruiser Diesel Inboard 2.8L

Бренд: Mercury Страницы: 93

LOMBARDINI 9 LD 625-2

Бренд: Kohler Страницы: 92

Бренд: Kohler Страницы: 4

Бренд: Brother Страницы: 42

Бренд: Northern Lights Страницы: 36

Бренд: Northern Lights Страницы: 45

Бренд: Northern Lights Страницы: 56

Бренд: Lenze Страницы: 36

MCA10I40 Series

Бренд: Lenze Страницы: 44

Smart Motor m300

Бренд: Lenze Страницы: 116

Бренд: Lenze Страницы: 72

Бренд: Hyundai Seasall Страницы: 150

Бренд: Volvo Penta Страницы: 53

Бренд: Volvo Penta Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды