Motorola APX 4000 Скачать руководство пользователя страница 480 | Manualshive

Страница: 480 / 526

background image

9-2

Basic Troubleshooting

: Operational Error Codes

9.2

Operational Error Codes

During radio operation, the radio performs dynamic tests to determine if the radio is working properly.
Problems detected during these tests are presented as error codes on the radio’s display. The
presence of an error code should prompt a user that a problem exists and that a service technician
should be contacted. Use

to aid in understanding particular operational error codes.

02/88

DSP RAM Fatal Error –

Note:

Not a checksum

failure

Turn the radio off, then on

02/90

General DSP Hardware Failure (DSP startup
message not received correctly)

Turn the radio off, then on

09/10

Secure Hardware Error

Turn the radio off, then on

09/90

Secure Hardware Fatal Error

Turn the radio off, then on

Hardware board absent

/

Hardware board absent

then

Man-Down Hw error

Keypad board is not connected properly to the
radio

Ensure the Keypad board is fixed
in place

15/10

External Accessory Non-Fatal Error
External Accessory is not present on power up
or did not power up correctly, and external
accessory feature is enabled in codeplug.

Verify external accessory is
connected and powers up. Turn
the radio off, then on.

15/90

External Accessory Fatal Error
External Accessory is not present on power up
or did not power up correctly, and external
accessory feature is enabled in codeplug.

Verify external accessory is
connected and powers up. Turn
the radio off, then on.

1E/10

Collaborative device is connected to the radio
but the collaborative feature is not enabled in
the codeplug.

Contact your Motorola Sales
Representative/Partner on how to
add Collaborative feature to your
radios.

Note:

If the corrective action does not fix the failure, send the radio to the depot.

Table 9-2. Operational Error Code Displays

Error Code

Description

Corrective Action

FAIL 001

Synthesizer Out-of-Lock

1. Reprogram external codeplug
2. Send radio to depot

FAIL 002

Selected Mode/Zone Codeplug
Checksum Error

Reprogram external codeplug

Table 9-1. Power-Up Error Code Displays (Continued)

Error Code

Description

Corrective Action

«
...
478
479
480
481
482
...
»

Содержание APX 4000















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для APX 4000

Бренд: Panasonic Страницы: 20

Бренд: Sealey Страницы: 4

Бренд: F&U Страницы: 10

Бренд: GENERGY Страницы: 90

Бренд: Fresh 'N Rebel Страницы: 10

Бренд: OWI Страницы: 1

Бренд: Milwaukee Страницы: 19

Бренд: Clatronic Страницы: 14

Бренд: THORLABS Страницы: 18

Бренд: Audio Pro Страницы: 53

Бренд: Roberts Страницы: 28

MagicMount MAGPBEZ

Бренд: Scosche Страницы: 4

IntelliChlor IC60

Бренд: Pentair Pool Products Страницы: 46

Бренд: Joy-it Страницы: 5

Бренд: Duracell Страницы: 41

Бренд: ISOUND Страницы: 3

Бренд: Sangean Страницы: 24

Бренд: Uniden Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды