Motorola APX 4000 Скачать руководство пользователя

Страница: 398 / 526

5-10

Performance Checks

: Transmitter Performance Checks

5.4

Transmitter Performance Checks

The following tables outline the performance checks for the transmitter.

Table 5-8. Transmitter Performance Checks – APX 2000/ APX 4000 (Two Knobs)

Test Name

System Analyzer

Radio

Test Set

Comments

Reference
Frequency

RF Control:

Monitor

Meter:

RF Display

Display:

Bar Graphs

Freq:

Selected radio TX

freq.

TEST MODE CSQ
channel* or
programmed
conventional
channel

PTT

to continuous

(during the
performance
check).

VHF:

±2 ppm

(272–348 Hz)

UHF1:

±2 ppm

UHF2:

±2 ppm

700/800 MHz:

±1.5ppm

(1146–1305 Hz)

RF Power

As above

VHF

: 1–5 Watt

UHF1

: 1–5 Watt

UHF2

: 1–5 Watt

700

: 1–2.7 Watt

800

: 1–3 Watt

Voice
Modulation
(external)

As above. Set fixed 1 kHz
audio level to 400 mV.

As above

Deviation:
(12.5 kHz)

≥

2.1 kHz, but

≤

2.5 kHz

(25 kHz)

≥

4.1 kHz, but

≤

5.0 kHz

Voice
Modulation
(internal)

RF Control:

Monitor

Meter:

RF Display

Display:

Bar Graphs

Freq:

Selected radio TX

freq.

As above

Remove
modulation input.

PTT

to OFF

(center)

Press

PTT

button on radio.

Say “four” loudly into the
radio mic. Measure
deviation:
(12.5 kHz)

≥

2.1 kHz but

≤

2.5 kHz

(25 kHz)

≥

4.1 kHz but

≤

5.0 kHz

PL Modulation
(radios with
conventional,
clear mode,
coded squelch
operation only)

As above

Conventional
coded squelch
personality (clear
mode operation)
or TPL channel
(test mode*)

PTT

to continuous

(during the
performance
check)

Deviation:
(12.5 kHz)

≥

375 Hz but

≤

500 Hz

(25 kHz)

≥

500 Hz but

≤

1000 Hz

Secure
Modulation
(radios with
conventional,
secure mode,
talkaround
operation only)

As above

Programmed
conventional
channel (secure
mode operation)
Load key into
radio.

As above

Deviation:

≥

3.7 kHz but

≤

4.3 kHz

See

Table 5-5

Содержание APX 4000















































































































































































































































































































































































































































































































































Результаты поиска

Содержание APX 4000

Отзывы:

Похожие инструкции для APX 4000

Бренды по названию

Популярные бренды

Motorola APX 4000, Базовое руководство по обслуживанию

Результаты поиска

Содержание APX 4000

Отзывы:

Похожие инструкции для APX 4000

Бренды по названию

Популярные бренды