Motion AXIS STUIFMEEL Thomson PC-Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 24

background image

Thomson

Thomson PC-Series™ Precision Linear Actuator - Installation Manual - June 2014

17

4.11.2 Motor installation on parallel style models with RediMount system

1. Make sure the extension tube is fully retracted

and then remove the sealing plug.

2. Press the motor shaft on to the coupling inside

of the belt gear flange.

3. Use a hexagon key to tighten the coupling

around the motor shaft. Correct tightening

torque for PC25 models = 0.85 Nm and for

PC32 and PC40 = 2.0 Nm.

4. Bolt the motor to the flange using four screws.

Tighten the screws according to table T6.3.1.

5. Put the sealing plug back.

4.11.3 Removal of motor from a unit with RediMount system

If removing a motor from a unit with RediMount system the extension tube must be fully extended to

make it possible to losen the coupling.

«
...
15
16
17
18
19
...
»

Содержание AXIS STUIFMEEL Thomson PC-Series

























Отзывы:

Нет отзывов

Похожие инструкции для AXIS STUIFMEEL Thomson PC-Series

Бренд: GARAN Страницы: 8

Бренд: Gamma Vacuum Страницы: 25

Бренд: Gamma Страницы: 28

Бренд: Jands Страницы: 7

Бренд: hager Страницы: 11

coviva Smartbox TKP100A

Бренд: hager Страницы: 34

Бренд: OJ Electronics Страницы: 8

Бренд: OJ Electronics Страницы: 112

Бренд: OJ Страницы: 17

Бренд: Rabbit Страницы: 38

Бренд: R82 Страницы: 8

Бренд: Paradox Страницы: 3

Бренд: MX Страницы: 12

Бренд: Sven Страницы: 6

Бренд: Viva Страницы: 9

Бренд: Gateway Страницы: 2

Бренд: CALEFFI Страницы: 6

Бренд: Oriental motor Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды