background image

8

2. Setting Up The Instrument 

Avoid placing the instrument in locations exposed to direct sun-
light, dust, vibration, high temperature and high humidity and 
where it is difficult to unplug the power supply cord.

2.1. Operating environment

 Indoor use

 Altitude: Max 2000 meters

 Ambient temperature: 15°C to 35°C

 Maximum relative humidity: 75% for temperature up to 31°C

decreasing linearly to 50% relative humidity at 40°C

 Supply voltage fluctuations: Not to exceed ±10% of the

normal voltage.

 Pollution degree: 2 (in according with IEC60664)

 Installation / Overvoltage category: 2

(in according with IEC60664)

 Air pressure of 75kPa to 106 kPa

 No hoar frost, dew, percolating water, rain

3. Assembling The Microscope

3.1. Verifying Input Voltage

 The automatic voltage selection works with a broad range of 

settings. However, always use a power cord that is rated for the 
voltage used in your area and that has been approved to meet
local safety standards. Using the wrong power cord could cause 
fire or equipment damage.

 In case of using the extension cord, use only a power supply 

cord with a protective earth (PE) wire.

 In order to prevent electric shock, always turn the power switch 

on the power supply off before connecting the power cord.

 Electrical Specifications:

a. Halogen

Input : 90-240V~, 38W, 50-60Hz (Hologen)
Lamp : 6V30W Halogen
Fuse : 250V T2.5A (If the original fuse is blown, please replace 
with specified fuse)

b. LED

Input : 90-240V~, 6W, 50-60Hz (LED)
Lamp : 3W LED
Fuse : 250V T1A (If the original fuse is blown, please replace 
with specified fuse)

3.2. Lamp and Lamp House Cover
(Replacing The Lamp)

The lamp and the lamphouse become very hot during and after 
a period of operation.
Risk of burn – Do not touch the lamp during or immediately 
after period of operation.
Make sure the lamp has cooled sufficiently before attempting 
to replace the lamp.

a. Halogen

 In order to prevent electric shock always turn the power 

switch off and unplug the power cord before installing or re-
placing the lamp.

 Place microscope on its back and pull back the lamp house 

cover plate.

 Firmly insert the lamp into the socket pinholes until it reach-

es the limit. Be careful not to tilt the lamp when mounting.

 When installing the lamp, do not touch the glass surface of 

the lamp with bare fingers. Doing so will cause fingerprints, 
grease, etc., to burn onto the lamp surface, reducing the illu-
mination provided by the lamp. If the surface is contaminated, 

Содержание BA210 series


















Отзывы: