fig 12
fig 13
fig 1.1
Large End
fig 1.2
Small End
fig 1.3
Back Board
Shelf
fig 1.7
fig 1.4
Middle Panel
Base Panel
fig 1.6
Front Plinth
fig 1.13
fig 1.11
Upper & Lower Drawer Fronts
Foot
fig 1.9
fig 1.5
Plinth Block
Brace
fig 1.8
fig 1.10
Doors
fig 1.15
Drawer Backs
fig 1.16
Drawer Sides
fig 1.14
Mattress Base
fig 1.17
Sides
fig 1.19
25 Large Cams
You need
a cross-head
screwdriver.
25 Large Cam pins
fig
1.26
36 Large
16 Short
screws (10mm)
fig
1.28
8 Small
cam pins
8 Small
cams
4 Hinge sets
2 Screw
Bolts (50mm)
fig
1.23
fig
1.24
6 Bolts (35mm)
fig
1.25
8 Bolts (16mm)
fig
1.27
1 Allen Key
fig
1.32
34 Small
Mattress Base screws
Ensure ‘cut out’ of mounting plate is at the front
C
A
B
Door
Do
r
o
Do
r
o
1
2
fig
1.29
fig
1.20
fig
1.21
fig
1.22
fig
1.31
fig
1.30
6
important notes
1
parts check list
Please take a few minutes to read this user guide.
Lay the parts out on the floor and compare to the PARTS CHECK LIST (below). Do not discard any
packaging until you are sure that you have all the parts.
You will need the aid of a second person at certain stages of assembly.
assembly
fig 2
CR
Insert the 4 shelf studs into the holes on the inside faces of the carcass (see fig 12.1). Once the studs have
been inserted into the correct position, carefully place the shelf into the unit. The shelf may need to be
placed at an angle to ease insertion.
1. Insert the door hinges into the large holes in the door and secure each with the 2 pre-fitted hinge screws
(see fig 12.2).
2. To attach the door, fit hinge slot “A” under bolt “B” and tighten bolt “B”.
Door adjustment may be made by slackening bolt “B” slightly and either tightening or loosening screw “C”
as appropriate. Finally, re-tighten “B” and the screws holding the hinge mounts to the side panel.
Attach the 4 mounting plates to the inside faces of the Carcass sides in the pre drilled pilot holes (as shown
in fig 12.2).
Please note: The mounting plates should be orientated with the long edge or cut out section at the front.
Carefully lift the mattress base onto the bed, webbing faced down, pull the mattress base
up to one end, then spread that slats out evenly. Use the 34 small mattress base screws to
secure the base to the bed through the holes in all slats.
Attach the base panel to the front plinth by
inserting 7 large cam pins and 4 dowels into
the front plinth as shown.
Also insert 7 large cams into the corresponding
larger holes on the face of the base panel.
Fit the two parts together by inserting the
exposed ends of the large cam pins and
dowels into the corresponding holes on the
front edge of the base panel. Make sure that
the arrows on the cams are pointing towards
the heads of the cam pins. Once all cam pins
and dowels are correctly engaged, tighten the
cams clockwise to secure.
Drawer Runners
fig 12.2
Shelf
fig 12.1
4 Shelf studs
fig
1.33
fig 1.18
Drawer Bases
fig 1.12
4 Screw
Bolts (40mm)
4 Short
screws (15mm)
fig
1.34
Dowels
