ELECTRICAL SYSTEM LEGENDE
GE_, MS_, TS_
M
60
© MOSA
REV.6-06/08
26/07/04 M60GB
A: Alternator
B: Wire connection unit
C: Capacitor
D: G.F.I.
E: Welding PCB transformer
F: Fuse
G: 400V 3-phase socket
H: 230V 1phase socket
I:
110V 1-phase socket
L: Socket warning light
M: Hour-counter
N: Voltmeter
P: Welding arc regulator
Q: 230V 3-phase socket
R: Welding control PCB
S: Welding current ammeter
T: Welding current regulator
U: Current transformer
V: Welding voltage voltmeter
Z: Welding sockets
X: Shunt
W: D.C. inductor
Y: Welding diode bridge
A1: Arc striking resistor
B1: Arc striking circuit
C1: 110V D.C./48V D.C. diode bridge
D1: E.P.1 engine protection
E1: Engine stop solenoid
F1: Acceleration solenoid
G1: Fuel level transmitter
H1: Oil or water thermostat
I1: 48V D.C. socket
L1: Oil pressure switch
M1: Fuel warning light
N1: Battery charge warning light
O1: Oil pressure warning light
P1: Fuse
Q1: Starter key
R1: Starter motor
S1: Battery
T1: Battery charge alternator
U1: Battery charge voltage regulator
V1: Solenoid valve control PCBT
Z1: Solenoid valve
W1: Remote control switch
X1: Remote control and/or wire feeder
socket
Y1: Remote control plug
A2: Remote control welding regulator
B2: E.P.2 engine protection
C2: Fuel level gauge
D2: Ammeter
E2: Frequency meter
F2: Battery charge trasformer
G2: Battery charge PCB
H2: Voltage selector switch
I2: 48V a.c. socket
L2: Thermal relay
M2: Contactor
N2: G.F.I. and circuit breaker
O2: 42V EEC socket
P2: G.F.I. resistor
Q2: T.E.P. engine protection
R2: Solenoid control PCBT
S2: Oil level transmitter
T2: Engine stop push-button T.C.1
U2: Engine start push-buttonT.C.1
V2: 24V c.a. socket
Z2: Thermal magnetic circuit breaker
W2: S.C.R. protection unit
X2: Remote control socket
Y2: Remote control plug
A3: Insulation moitoring
B3: E.A.S. connector
C3: E.A.S. PCB
D3: Booster socket
E3: Open circuit voltage switch
F3: Stop push-button
G3: Ignition coil
H3: Spark plug
I3: Range switch
L3: Oil shut-down button
M3: Battery charge diode
N3: Relay
O3: Resistor
P3: Sparkler reactor
Q3: Output power unit
R3: Electric siren
S3: E.P.4 engine protection
T3: Engine control PCB
U3: R.P.M. electronic regulator
V3: PTO HI control PCB
Z3: PTO HI 20 l/min push-button
W3: PTO HI 30 l/min push-button
X3: PTO HI reset push-button
Y3: PTO HI 20 l/min indicator
A4: PTO HI 30 l/min indicator
B4: PTO HI reset indicator
C4: PTO HI 20 l/min solenoid valve
D4: PTO HI 30 l/ min solenoid valve
E4: Hydraulic oil pressure switch
F4: Hycraulic oil level gauge
G4: Preheating glow plugs
H4: Preheating gearbox
I4: Preheating indicator
L4: R.C. filter
M4: Heater with thermostat
N4: Choke solenoid
O4: Step relay
P4: Circuit breaker
Q4: Battery charge sockets
R4: Sensor, cooling liquid temperature
S4: Sensor, air filter clogging
T4: Warning light, air filter clogging
U4: Polarity inverter remote control
V4: Polarity inverter switch
Z4: Transformer 230/48V
W4: Diode bridge, polarity change
X4: Base current diode bridge
Y4: PCB control unit, polarity inverter
A5: Base current switch
B5: Auxiliary push-button ON/OFF
C5: Accelerator electronic control
D5: Actuator
E5: Pick-up
F5: Warning light, high temperature
G5: Commutator auxiliary power
H5: 24V diode bridge
I5: Y/s commutator
L5: Emergency stop button
M5: Engine protection EP5
N5: Pre-heat push-button
O5: Accelerator solenoid PCB
P5: Oil pressure switch
Q5: Water temperature switch
R5: Water heater
S5: Engine connector 24 poles
T5: Electronic GFI relais
U5: Release coil, circuit breaker
V5: Oil pressure indicator
Z5: Water temperature indicator
W5: Battery voltmeter
X5: Contactor, polarity change
Y5: Commutator/switch, series/parallel
A6: Commutator/switch
B6: Key switch, on/off
C6: QEA control unit
D6: Connector, PAC
E6: Frequency rpm regulator
F6: Arc-Force selector
G6: Device starting motor
H6: Fuel electro pump 12V c.c.
I6: Start Local/Remote selector
L6: Choke button
M6: Switch CC/CV
N6: Connector – wire feeder
O6: 420V/110V 3-phase transformer
P6: Switch IDLE/RUN
Q6: Hz/V/A analogic instrument
R6: EMC filter
S6: Wire feeder supply switch
T6: Wire feeder socket
U6: DSP chopper PCB
V6: Power chopper supply PCB
Z6: Switch and leds PCB
W6: Hall sensor
X6: Water heather indicator
Y6: Battery charge indicator
A7: Transfer pump selector AUT-0-MAN
B7: Fuel transfer pump
C7: „GECO“ generating set test
D7: Flooting with level switches
E7: Voltmeter regulator
F7: WELD/AUX switch
G7: Reactor, 3-phase
H7: Switch disconnector
I7: Solenoid stop timer
L7: "VODIA" connector
M7: "F" EDC4 connector
N7: OFF-ON-DIAGN. selector
O7: DIAGNOSTIC push-button
P7: DIAGNOSTIC indicator
Q7: Welding selector mode
R7: VRD load
S7: 230V 1-phase plug
T7: V/Hz analogic instrument
U7: Engine protection EP6
V7: G.F.I. relay supply switch
Z7: Radio remote control receiver
W7: Radio remote control trasnsmitter
X7: Isometer test push-button
Y7: Remote start socket
A8: Transfer fuel pump control
B8: Ammeter selector switch
C8: 400V/230V/115V commutator
D8: 50/60 Hz switch
E8: Cold start advance with temp. switch
F8: START/STOP switch
G8: Polarity inverter two way switch
H8: Engine protection EP7
I8: AUTOIDLE switch
L8: AUTOIDLE PCB
M8: A4E2 ECM engine PCB
N8: Remote emergency stop connector
O8: V/A digital instruments and led VRD PCB
P8: Water in fuel
Q8:
R8:
S8:
T8:
U8:
V8:
Z8:
W8:
X8:
Y8:
Содержание DSP 400 YSX
Страница 50: ......
