background image

The Specialist In Drum Handling Equipment

Model 82H-125

Mobile Lifter / Palletizer  

with DC Power Lift

operator’s Manual for Model 82H-125 Morse Mobile Lifter / Palletizer

serial number 0312 to ____ (MMYY)

morsedrum.com

Copyright 2019  -  Morse Mfg. Co., Inc. 

 

Form PL82H-125 (0312-____) 

(Updated 12 Jun, 2019 3:15 PM)

 

             

4

operating Instructions

Roll drum lifter to drum. Steer unit so head and bottom support meet 

1. 

centerline of drum.  Head should push into side of drum near drum top. 

Exact height is not critical. Jaws should arrive below drum rim. This 

usually corresponds to having top of head about as high as top of drum. 

 

WARnInG:

 Keep hands and other objects away from top opening of 

lifting frame.  

To clamp drum: Operate lift function to raise head while it is held against 

2. 

the drum. Drum-gripping action is automatic as the head rises. This is 

how it works: As the head rises, the lower jaw will come up under the lip 

of the drum rim, “catch” under it, and be held down. As the head rises with 

the lower jaw thus held by the drum rim, internal linkage will pull the upper 

jaw downward to meet the top of the drum rim. The drum’s weight on the 

lower jaw creates the force that pulls the upper jaw down to tightly grip the 

drum rim. No manual contact is required. 

 

WARnInG:

 Keep hands and other objects away from drum-gripping 

jaws. 

With drum held off the floor, push drum lifter to deliver drum. Avoid 

3. 

unreasonably rough or non-level surfaces. Move at moderate speed. 

Carry drum only high enough to avoid contact with the floor or obstacles. 

Push loaded unit when possible for transporting. Pulling unit should be 

limited to maneuvering at short distance. 

 

WARnInG:

 

excessive pitching or bouncing caused by rushing over 

rough or non-level floors can make drum momentarily weightless, 

jaws can disengage.

 

To release drum at intended destination: operate control to lower drum 

4. 

onto level floor or pallet. When drum comes to rest and head continues 

to lower, weight will no longer be on the lower jaw and jaws will open 

automatically. No manual contact is required. Do not stop lowering as 

soon as drum touches down, keep going down for a few more inches. Pull 

unit away once upper jaw has retracted clear of drum rim. Park unit on 

level floor, out of traffic lanes when not in use.

 

Adjustment for Shorter Drums: The head is factory set in upper position 

5. 

for handling drums at least 34” tall, including typical 55 gallon drums. 

For handling drums as short as 22”, relocate head downward as follows: 

Detach head by removing nuts that hold head to lifting assembly. 

Reattach head at alternate location 12” lower.

Maintenance

Periodic inspection for the general condition of structural and mechanical components is imperative for safe and efficient operation.

• 

Periodically inspect all moving parts, framework, and contact areas for signs of wear, fatigue, or loosening.  Tighten, adjust, or 

• 

replace parts as necessary to prevent failure and maintain proper function.

Inspect the hydraulic system for oil drips, hose damage, or other signs of wear.  Inspect the level and condition of the hydraulic fluid.  

• 

Replace any parts that show signs of wear.

Grease wheel bearings periodically. Clean and lubricate all moving parts including: Cylinder pin and linkages.

• 

Worn or damaged parts must be properly replaced with the correct, genuine Morse parts.

• 

Hydraulic pump is shipped filled with Noco Premium plus automatic transmission fluid d/m. Material safety data sheet (msds) is 

• 

available online. Change oil yearly, sooner depending on dirty conditions or outdoor use. Replace oil with Mobil dte 24 or equivalent 

for indoor use (Mobil dte 13 for outdoor use).

Содержание 82H-125

Страница 1: ...defects in workmanship or materials for two years when used properly within its rated capacity Warranty does not cover wear from normal use or damage from accident or abuse Motors and other purchased parts carry the warranties of their manufacturers For warranty claims contact your Morse Dealer to obtain a return authorization number and for return freight advice Return freight must be prepaid In ...

Страница 2: ...Any modifications may void the warranty This machine was designed to perform a specific job and alterations may result in injury to operator or machine WARNING No Loose Fitting Clothing Wear close fitting clothing and safety equipment appropriate to the job Loose fitting clothing may become caught on the machinery and cause severe personal injury WARNING Hydraulic Fluid Under Pressure Can Be Hazar...

Страница 3: ...eters with a minimum drum height of 28 Drums should weigh at least 75 Lb to complete clamping action The maximum capacity is 1000 Lb Controls The Morse Mobile Lifter Palletizer is manually propelled and steered LIFT and Lower Function Figure 2 3 To raise the drum Push and hold the valve handle in against the start switch Release the handle when the drum is at the desired height To lower the drum P...

Страница 4: ...ough or non level floors can make drum momentarily weightless jaws can disengage To release drum at intended destination operate control to lower drum 4 onto level floor or pallet When drum comes to rest and head continues to lower weight will no longer be on the lower jaw and jaws will open automatically No manual contact is required Do not stop lowering as soon as drum touches down keep going do...

Отзывы: