background image

The Specialist In Drum Handling Equipment

MODEL 80i

Mobile-Karrier

Operator’s Manual for Model 80i Morse Mobile-Karrier

Serial Number 1114 to 0515 (MMYY)

morsedrum.com

Copyright 2015  -  Morse Mfg. Co., Inc. 

 

Form PL80i (1114-0515)  (Updated April 29, 2015 1:02 PM)

               

2

Safety Information

 (continued)

DANGER

 

- Indicates a situation which, if not avoided, will result in serious injury or death.  

This signal word is limited to the most extreme situations.

WARNING

 

-  Indicates  a  situation  which,  if  not  avoided,  could  result  in  serious  injury  or 

death.

CAUTION

 

- Indicates a situation which, if not avoided, can result in damage to the machine.

CAUTION

 

– Do Not Transport with Drum Raised. Always lower the drum holder to lowest position 

before transporting.

WARNING

 

- The Mobile-Karrier is designed to handle one drum of the types listed at the top of page 3.  

Machine Description.  DO NOT attempt to handle any other type of drum or object.  DO NOT exceed 

the weight capacity of 800 Lb.

WARNING

 

- Level Floors Only 

 

For operation only on clean, level floors of suitable bearing capacity. Do not use on sloped surfaces, 

ramps, irregular or debris strewn floors.

WARNING

 

- Do Not Modify the Unit. Under no circumstances should any modifications be made to 

the Morse machinery without factory authorization.  Any modifications may void the warranty.  This 

machine was designed to perform a specific job and alterations may result in injury to operator or 

machine.

WARNING

 

- No Loose Fitting Clothing. Wear close-fitting clothing and safety equipment appropriate 

to the job.  Loose fitting clothing may become caught on the machinery and cause severe personal 

injury.

CAUTION

 

- Wear safety shoes with non-slip soles and hard toe protection.

CAUTION

 

- DO NOT allow drum to impact on floor, ground, or dumping station, etc.

Содержание 80i








Отзывы: