background image

The Specialist In Drum Handling Equipment

Model 400A-60-124

Hydra-Lift, 60”, Air Power Lift, Manual Tilt

Operator’s Manual for Morse Hydra-Lift Karrier Model 400A-60-124

Serial Number 1210 to ____ (MMYY)

morsedrum.com

Copyright 2022 - Morse Mfg. Co., Inc. 

 

Form OM400-60-124 (1210-____)   

(Updated 3 Mar, 2022)

 

4

Figure 2.3

WARNING

 - Watch Out for Pinch Points

Stay clear of moving parts.  Operator should 

remain behind the push handle during the 

lift operation.

Floor Lock

The screw-down floor lock is located on the base of the tower 

(figure 3.1).  Turning the floor lock clockwise until it locks in the 

down position activates the floor lock.  When the floor lock is 

activated it prevents unwanted free wheeling of the unit.  Floor 

conditions determine the effectiveness of the floor lock.  The 

operator should verify its holding action before depending on it to 

hold.

Drum Holder Assembly

The MORCINCH

TM

 Drum Holder (Saddle) assembly is the 

component on intended to hold the drum.  It is designed to secure 

a standard ribbed 55-gallon (210 liter) steel drum around it’s middle 

using a cinch chain and ratchet tightening system.  It automatically 

adjusts for 22” to 23.5” (56 to 59.7 cm) diameter drum.

The MORCINCH

TM

 Drum Holder also accepts accessories to 

handle a plastic drum, fiber drum, or a smaller diameter drum.

Figure 3.1

Controls

The Morse Hydra-Lift Karrier is manually propelled and steered. The drum lift is 

powered by an air motor with an on/off valve. There are two functions for the operator 

to control (Figure 2.3):

1. 

LIFT and Lower Function to raise and lower the drum

• 

Plug your air line into the on/off air valve.

• 

Turn the motor on by holding the valve handle in the on position. The drum will 

lift.

• 

Release the valve handle when the drum is at the desired height.

• 

To lower the drum: With the motor off, push in the LOWER handle.

 

2.  TILT Function to control the degree of rotation of the drum.

• 

Turn the hand crank to turn the drum.

• 

Before releasing your grip on the hand crank, pull out the crank stop pin to block 

the hand crank from spinning freely.

• 

If the drum handler is equipped with the MORStop Tilt-Brake, there is no need 

to use the stop pin. Braking is immediate and self-actuating, without additional 

steps by the operator.

Note: To add the MORStop Tilt-Brake to an existing drum handler, order part # 3900-

P for a field installation kit.

Содержание 400A-60-124







Отзывы: