manualshive.com logo in svg

Morningstar SureSine 1000 W, Инструкция по установке и эксплуатации, Страница: 41 / 66

Поделиться
Скачать
Morningstar SureSine 1000 W Скачать руководство пользователя страница 41

31

OPERATION

MS-003650  

(Rev  0 Draft 10)

3.2  AC Output Mode Switch Operation

The AC Output Mode Switch will always turn the inverter on directly in the ON (up) 
position.  To enable ON/OFF control with a wired remote switch or a communication 
command (digital command), the switch must be in the REMOTE position. Select 
remote switch or digital command using DIP Switch # 1.

Figure 24:   AC Output Mode Operation and Bluetooth Activation

3.3  

Protections

3.3.1 

Low Voltage Disconnect (LVD)

The SureSine will disconnect AC Output when the battery discharges 
below the Low Voltage Disconnect (LVD) set point (after a 4-minute delay).  
AC Output will resume when the battery has recharged to Low Voltage 
Reconnect (LVR) set point.  The LVD/LVR thresholds are adjustable using DIP 
Switch 4.  See "Adjusting Settings" on page 11 for details.  

Audible LVD Warnings:  

•  The SureSine will beep four (4) times when the battery discharges to the 

LVD Warning threshold voltage.  

•  The SureSine will beep twice when Low Voltage Disconnect occurs.  

•  The LVD Warning occurs 0.3 V above the selected LVD threshold. 

Содержание SureSine 1000 W



































































Отзывы:

Нет отзывов