Morningstar SureSine 1000 W Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 66

Morningstar SureSine 1000 W Скачать руководство пользователя страница 3

MS-003650

MORNINGSTAR

World’s Leading Solar

Controllers

&

Inver ters

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

- This manual contains important safety, installation, and operating

instructions for the Morningstar SureSine Inverter.

The SureSine produces voltages and currents capable of causing severe injury or death. Extreme
caution must be taken when installing and using the SureSine.

The following symbols are used throughout this manual to indicate potentially dangerous conditions
or important safety instructions.

WARNING

: Indicates a potentially dangerous condition.

Failure to observe this notice could result in severe personal
injury or death.

CAUTION:

Indicates a critical procedure for safe and proper

operation of the SureSine. Use extreme caution when
performing this task. Failure to observe this notice could result
in personal injury or equipment damage.

NOTE:

Indicates a procedure or function that is important to

the safe and proper operation of the SureSine Inverter.

GENERAL SAFETY INFORMATION

Throughout this manual, NEC guidance has been provided in order to meet general safety
requirements and inform best installation practices. It is the installer’s responsibility to ensure that the
Installation complies with all local safety and code requirements.

• Read all of the instructions and cautions in the manual before starting the installation.

• Ensure that battery power has been disconnected BEFORE installing, servicing, or removing

the SureSine Inverter.

• Do not allow water to enter the SureSine.

• Avoid wearing jewelry while installing this equipment.

• Do not smoke near the battery bank.

• Ensure power connections remain tight to avoid excessive heating from a loose connection.

• Recycle the battery when it is replaced.

«
1
2
3
4
5
...
»

Содержание SureSine 1000 W



































































Отзывы:

Нет отзывов