![background image](http://html.mh-extra.com/html/monzana/104404/104404_instructions-manual_1831153015.webp)
15
www.DeubaXXL.de
0. Place the tower fan on a slightly elevated surface so the bottom end protrudes
slightly to fasten the foot. If necessary, place a sheet or blanket beneath the product to
protect the surface.
1. To assemble the stand, simply snap the two halves (B & C) together (Fig. 1).
2. Pull the power cord through the assembled stand, making sure the wider end of the
stand is facing towards the fan housing (Fig. 2).
3. Align the hole “A” located at the bottom of the fan housing with the post “A” on the
top end of the stand. Insert the post into the hole (Fig. 3).
4. Secure the stand to the fan housing with 4 screws (M4x10 mm). Tighten the screws
with a screwdriver (Fig. 4).
5. Feed the power cable through the middle of the foot and then stick the foot
together. Make sure the flat side is down. Snap the two base halves (E & F) together by
sliding the posts of one base half into the slots of the second base half (Fig. 5).
0. Place the tower fan on a slightly elevated
surface so the bottom end protrudes slightly to
fasten the foot. If necessary, place a sheet or
blanket beneath the product to protect the
surface.
1. To assemble the stand, simply snap the two
halves (B & C) together (Fig. 1).
2. Pull the power cord through the assembled
stand, making sure the wider end of the stand is
facing towards the fan housing (Fig. 2).
3. Align the hole “A” located at the bottom of the
fan housing with the post “A” on the top end of
the stand. Insert the post into the hole (Fig. 3).
4. Secure the stand to the fan housing with 4 screws
(M4x10 mm). Tighten the screws with a
screwdriver (Fig. 4).
5. Feed the power cable through the middle of
the foot and then stick the foot together. Make
sure the flat side is down. Snap the two base
halves (E & F) together by sliding the posts of one
base half into the slots of the second base half
(Fig. 5).
6. Pull the power cable through the central hole
of the already assembled base plate. Align the
post “B” located at the bottom of the stand with
the hole “B” located on the central hole. Then
insert the posts into the holes (Fig.6).
7. Secure the base plate to the stand by 4 screws
❸
❹
❺
❻
❼
❽
COMPONENTS
TECHNICAL DATA
ASSEMBLY
1
3
5
7
2
4
6
1
Remote control
2
Control panel
3
LED panel
4
Air outlet
5
Front housing
6
Stand
7
Base plate
Rated voltage
220-240 V ~ 50 Hz
Rated power
45 W
❶
❷
Hole “A”
Post “A”
4 screws
(M4x10 mm)
Post “B”
Hole “B”
4 screws
(M4x10 mm)
12
13
www.Deuba24online.de
www.Deuba24online.de
Содержание 104404
Страница 5: ...5 www DeubaXXL de TEIL NR STK 1 1 COA COB 1 COC 1 COD 1 COE 1 COF 8 COG POWER SPEED MODE TIMER OSC ...
Страница 13: ...13 www DeubaXXL de TEIL NR STK 1 1 COA COB 1 COC 1 COD 1 COE 1 COF 8 COG POWER SPEED MODE TIMER OSC ...
Страница 21: ...21 www DeubaXXL de TEIL NR STK 1 1 COA COB 1 COC 1 COD 1 COE 1 COF 8 COG POWER SPEED MODE TIMER OSC ...
Страница 27: ...27 www DeubaXXL de ...