Montigo PL38DF Скачать руководство пользователя страница 18

Страница: 18 / 42

Page 18

PL38DF* Indoor Gas Fireplace

XG0216 - 160215.1

Installation

Section 3-3-3: Heat Shields

Installing a Wall Mounted RHS8 Heat shield

The RHS8 Heat shield CANNOT be used when the Termination is

WITHIN (36" Min. horizontal and 60" Min. vertical) from the fireplace,

or directly off the rear of the fireplace, as shown figure 17a. The

RHS101 Heat Shield (Figure 18c and 18d) MUST be used within the

noted dimensions.
To install the RHS8, frame an opening in combustible construction,

Figure 17 below. Slide the Heat shield in place over the vent pipe

which attaches to the fireplace. After the fireplace and vent pipe

has been installed, clearances should match the dimensions in

Figure 17a.

Installing a Wall Mounted RHS101 Heat shield.

The RHS101 Heat shield MUST be used where the RHS8 Termination

(Figure 17 and 17a) CANNOT be used. Use the RHS101 where any

of the dimensions are within the parameters shown, figure 17a.

To install the RHS101, Slide the Inner Section over the vent pipe

that will connect to the fireplace. Then fasten the vent pipe to the

back of the fireplace with a minimum of three sheet metal screws.

From the outside slide the RHS101 outer section on see Figure 18.

To complete the installation fasten the Heat Shield Outer Section

& Termination frame to the structure Figure 18a.

Figure 17.

RHS8 Installation. (Install by sliding over vent pipe where it

passes through the combustible construction).

Figure 18. RHS101 Installation. (Install by sliding Outer Section over vent

pipe where it passes through the combustible construction.

Figure 17a.

RHS8 Installation. (Minimum requirements).

RHS8 Heat Shield

1” Min. Both sides Typical

1” Min.

Combustible Framing

Figure 18b.

RHS101 Installation.

Outer Shield 10 1/4”

3/8” Min. Both sides Typical

3/8” Min.

3/8” Min .

Combustible Framing

12” x 12”

Inner Shield 9 3/8”

Figure 18a. RHS101 Heat Shield after sliding the outer section in place.

Termination

Drywall / sheetrock
RHS101 Heat Shield, inner Section

RHS101 Heat Shield

Outer Section

Combustible

framing

Termination

Drywall / sheetrock
RHS101 Heat Shield, inner Section

RHS101 Heat Shield

Outer Section

Vent pipe, from fireplace

RHS8 Heat

Shield

36” Min

60” Min.

PTO Termination

Note: Images are shown without screens for clarity purposes.

However, your fireplace should not be operated without proper

installation of screens.

Содержание PL38DF











































Результаты поиска

Содержание PL38DF

Отзывы:

Похожие инструкции для PL38DF

Бренды по названию

Популярные бренды

Montigo PL38DF, Инструкция по установке и обслуживанию

Результаты поиска

Содержание PL38DF

Отзывы:

Похожие инструкции для PL38DF

Бренды по названию

Популярные бренды