6
MAINTENANCE
USING GRILL WITH ON-BOARD LPG (PROPANE) SYSTEMS
Propane (LPG)
Gas Regulator
A10-225 LPG (Propane)
10' Gas Grill Connection Kit
To other LPG
appliance
or use cap
Shut off
valve
Cylinder Valve
Gauge
Type 3
Valve
Solenoid
Gourmet
Gas Grill
Typical Marine &
R.V. Application
Align valve stem key
to valve chamber
lock detent and rotate
Gourmet
Gas Grill
Gourmet
Gas Grill
Type 3
Valve
• Magma On-Board LPG (Propane) Valves
and Hose Kits allow Magma Grills to be
installed within a boats existing on-board,
pre-regulated low pressure LPG (Propane)
system.
• Use only
Magma Type 3 Low
Pressure LPG (Propane) Valves.
See
our
Valve Application Guide
at
www.
MagmaProducts.com
for correct valve.
• In North America use
Magma A10-225
LPG 10' Hose Kit
in conjunction with
Type 3 Valve.
Outside North America check
your local dealer for proper hose and fittings.
• A primary shutoff valve
(supplied with
A10-225 hose kit)
must be used with this
control valve at point of connection into
your system. This allows shut off of gas
supply to hose leading to grill.
Stainless steel contrary to popular belief can rust. Most commonly, deposits on surface of the product will trap
moisture. It is this moisture that robs stainless steel of oxygen. Oxygen is the element that reacts with stainless steel
to form a protective layer of chrome oxide. Robbed of oxygen, this reaction does not take place and “crevice
corrosion” or “surface rusting” occurs. To minimize this effect, thoroughly clean your grill with soap and water, rinse
with fresh water, and dry. Avoid using stainless steel polishes on grill exterior as most leave a residue that may
discolor when grill is heated.
Additionally, stainless steel that is exposed to high heat will change color and texture over time. “Bluing” and
“browning” of grill exterior and internal components is not a failure of the stainless steel and will not affect
products operation. However, prolonged exposure to extreme high heat will cause chromium and nickel to “burn
out” of stainless steel. At this point stainless steel will become more susceptible to corrosion and will start to
deteriorate. We recommended replacement of internal components as they become seriously deteriorated.
We recommend thoroughly cleaning grill and internal components after each outing. Disassemble interior
components and remove all food residue. Use a “Scotch Brite” pad or similar product and “Easy-Off” oven cleaner
for cleaning grills interior components, followed by thoroughly washing with soap and water, rinse with fresh water
& dry. We also recommend using
“Magma Magic” Grill Restorer
for helping return your grill to its original luster.
AVOID CONTACT OF OVEN CLEANER OR GRILL RESTORER WITH SKIN, CONTROL VALVE, IGNITOR ELECTRODE &
WIRE, AND BOAT SURFACE. CAUTION: DO NOT USE ANY TYPE OF ABRASIVE PAD ON EXTERIOR MIRROR FINISH AS
IT WILL SCRATCH SURFACE, USE ONLY A SOFT CLOTH. We recommend covering grill between uses. Grill covers are
available at Magma retailers or directly from Magma. See our website,
www.magmaproducts.com
Grill Grates -
Clean with brass wire brush while grill is warm. Use Oven & Grill cleaner for burnt-on residue. Wash
with soapy water and dry prior to storage.
Ceramic Electrode -
Located just beside the burner, it should be kept clean of grease and debris. Be careful not
to damage the ceramic insulation or the wire. See page 5 for electrode spark adjustment.
Control Valve -
All valves are set and tested at our factory. Do not attempt to adjust or disassemble the valve in
any way. Call Magma if you suspect it is not adjusted properly. Clean valve with a cloth and remove any debris
obstructing the orifice.
Repair/Replacement Parts -
All replacement parts are readily available at your Magma Retailers or directly from
Magma. For a complete list of replacement parts visit our website
www.MagmaProducts.com
.
