background image

© 2013 Monte Carlo Fan Company

6/15/2013

3

Before you begin installing the fan, Switch power off

at Service panel and lock service disconnecting

means to prevent power from being switched on ac-

cidentally.  When the service disconnecting means

cannot be locked, securely fasten a prominent warn-

ing device, such  as a tag, to the service panel.

1

Before installing this fan make sure the outlet

box is properly installed to the house structure.

To reduce the risk of fire, electric shock, or per-

sonal injury, mount to outlet box or supporting

system acceptable for fan support. 

(Mounting must support at least 35 lbs.)

2

Thread safety cable through center

hole of the mounting plate. Thread

your house wires through center hole

also.These will be needed for wiring

of the fan.

4

Securely attached the mounting plate

to the outlet box using two screws

supplied by the outlet box. 

Use

metal outlet box suitable for fan

support (must support 35 lbs).

6

Place the decorative ring on the

motor housing.

3

Make wire connections to power source using

wire nuts provided.  Make sure that no filiments

are outside of the wirenut. After making the

wire connections, the wires should be spread

apart with the grounded conductor and the

equipment-grounding conductor on one side of

the outlet box and ungrounded conductor on the

other side of the outlet box.  

9

Connect black and blue wire from fan to Black

or (Hot) wire from house.  Connect White wire

from Fan to White (Neutral) wire from house.

Connect Ground leads from mounting bracket

and downrod to Ground lead from house.

Refer to Safety Tips section of manual.

8

Carefully lift the fan motor assembly

and engage the slot in the motor

housing with the hook on the mount-

ing plate so that the motor is se-

curely suspended.

7

For Canadian installation and for USA fan and

light kit combinations over 35 lbs, in both flush

and downrod mode the safety cable must be in-

stalled into the house structure beams using the

3” lag screws provided.  Make sure that when

the safety cable is fully extended the leadwires

are longer than the cable and no stress is placed

on the leadwires. 

Note

:If Installing The Second-

ary Support Safety Cable in the U.S., Do Not Re-

move Knockouts In The Outlet Box. 

5

Safety cable installation

Safety Cable

Lag Screw

Lag Screw

Safety Cable

Washer

Lock Washer

Содержание 5TV52XXD Series








Отзывы: