background image

5

12

13

14

15

16

17

© 2022 Monte Carlo Fan Collections

3/2022

Remove every other screws from yoke 

located on top of fan assembly. Keep 

screws.

Note

: Flush mount is not available with 

vaulted ceiling. 

Reinstall the 3 set screws remove in step 

12. Tighten screws securely. 

To prepare the fan for wiring, hang fan 

onto mounting bracket by sliding the 

canopy over the mounting bracket hook 

(

Use one of non-slotted holes on the 

rim of the canopy

).

For Canadian installation and for USA fan 

and light kit combinations over 35 lbs, in 

both flush and downrod modes the safety 

cable must be installed into the house 

structure beams using 3” lag screws, 

washers and lock washers provided. 

Make sure that when the safety cable is 

fully extended the lead wires are longer 

than the cable and no stress is placed on 

the lead wires.

Note

: If Installing The Secondary Support 

Safety Cable in the U.S., Do Not Remove 
Knockouts In The Outlet Box.

 

Make wiring connections using wire 

connectors provided as indicated above.  

White from fan to White (Neutral) from 

house. Black and Blue from fan to Black 

(Live) from house. Connect all green 

grounded wires to Grounded wire from 

House. Make sure that no filaments are 

outside of the wire connectors.

After making the wire connections, the wires 

should be spread apart with the grounded 

conductor and the equipment-grounding 

conductor on one side of the outlet box and 

ungrounded conductor on the other side of 

the outlet box. The splices after being made 

should be turned upward and pushed carefully 

up into the outlet box.              

Remove side covers from canopy 

exposing  4 holes.  2 closed holes and 2 

open “L” shape holes. 

Place rubber pad and canopy over lead 

wire and safety cable and align the larger 

holes in canopy and holes on rubber pad 

with the set screws on yoke. 

 

Side cover

Rubber pad 

Lag screw

Safety cable

Washer

Lock washer

SAFETY CABLE INSTALLATION

Wall switch

Power

source

White

(Natural)

Black

(Live)

Black

Blue

White

Grounded/

Green

Flush Mount Installation

Hook

Содержание 5LD52 Series









Отзывы: