background image

3

© 2019 Monte Carlo Fan Company

4/2019

1

2

3

4

5

6

ON

OFF

ON

OFF

Before you begin installing the fan, Switch 

power off at Service panel and lock 

service disconnecting means to prevent 

power from being switched on 

accidentally. When the service 

disconnecting means cannot be locked, 

securely fasten a warning device, such  

as a tag, to the service panel.

Use AC 120V/60HZ power supply 

only.

Before installing this fan make sure the 

outlet box is properly installed to the 

house structure. To reduce the risk of 

fire, electric shock, or personal injury, 

mount to outlet box or supporting system 

acceptable for fan support. 

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan 

support and use only the screws provided 

with the outlet box  (must support 35 lbs). 

Before attaching fan to outlet box, ensure 

the outlet box is securely fastened by at 

least two points to a structural ceiling 

member ( a loose box will cause the fan to 

wobble). Remove the two outlet box 

screws provided with the box, aligning 

the holes of the mounting bracket with 

the holes of the outlet box. Reinstall the 2 

outlet box screws securely.

Partially loosen downrod set screws from 

yoke at top of motor assembly.

Remove preassembled cross pin and 

keeper pin from downrod. 

Place downrod over canopy and canopy 

bottom ring. Thread lead wires and safety 

cable from motor assembly through 

downrod.

Slip downrod into motor housing yoke, 

aligning holes and install cross pin and 

keeper pin. 

Insert cross pin through yoke and downrod 

until point appears on the other side, and 

insert keeper pin on cross pin. 

Pull the downrod up tight against the 

cross pin, and then evenly tighten the 

downrod set screws on motor housing 

yoke. 

Warning

: Cross pin and keeper pin must 

be installed securely, failure to install them 

will result in serious injury.

Mounting bracket

Downrod

Cross pin

Cross pin

Keeper pin

Keeper pin

Canopy

Downrod

Canopy bottom ring

Downrod Mount Installation

Содержание 5HVDC52D Series










Отзывы: