background image

© 2013 Monte Carlo Fan Company

11/15/2013

6

Remove switch cap housing from fan.

Remove the plug of fitter. Install

switch cap housing to light kit by

turning clockwise to tighten.

28

Install keeper nut over lead wires.

29

Tighten keeper nut onto threaded

pipe from the light kit.

30

Install 2 x 13 watt GU24 base CFL bulbs. Bulbs

Included. 

WARNING: Over lamping the

fan will result in the fan lights shutting

down until the proper wattage of bulbs

are installed. Reset the lights by turning

off the wall switch, breaker, or by remote.

Replace bulbs with the correct wattage

bulbs, turn the power on.

31

Locate blue and white wire from the fan

marked “For light kit”.  Connect blue from fan

to black from light and white from fan to white

from light by pushing connectors together.

32

Attach switch cap to fan by lining up

2 slot ear holes and 1 screw hole and

twisting cap. Then tighten the 3

screws. 

33

Remove nut and save for next step.

27

Remove finial nut, finial cap, hex nut

and rubber washer from fitter and

save. 

34

Attach the glass to the light fixture.

Install the rubber washer first and

then the hex nut to the glass to se-

cure in place.

35

Содержание 5HM52 ND Series










Отзывы: