Monoprice 21824 Скачать руководство пользователя страница 6

Страница: 6 / 34

lectrical

ower

This 3D printer

uses an AC adapter with an output of 12 VDC, and an input of 110 or

240 VAC, 50/60 Hz. Ensure that your electric outlets provide power in this range.

- Do not allow anything to rest on the power cord. Do not locate this product where

people will walk on the cord.

- If an extension cord is used with this product,

sure that the total ampere rating

of the

equipment plugged into the extension cord does not exceed the extension

cord

ampere rating. Also,

sure that the total rating of all products plugged

into the wall

outlet does not exceed the fuse rating.

- Do not overload a power outlet, strip

or receptacle by plugging in too many devices.

- Use the product only with the supplied power supply cord set. If you need to

replace

he power cord set, make sure that the new power cord meets the

following

requirements: detachable type, UL listed/CSA certified, VDE approved or its equivalent,

4.5 meters (15 feet) maximum

- In case of malfunction

immediately

unplug the printer

from

the power source

- Do not attempt to fix this product by yourself, as opening or removing covers may

expose you to dangerous voltage points or other risks.

For

service, contact

Monoprice T

echnical

Support at [email protected]

Unplug this product from the wall outlet and refer servicing to qualified service personnel

when:

- The power cord or plug is damaged, cut

or frayed.

- Liquid was spilled into the product.

- The product was exposed to rain or water.

- The product has been dropped or the case has been damaged.

- The product exhibits a distinct change in performance, indicating a malfunction.

The product does not operate normally after following the operating instructions.

- Keep the printer out of the reach of small children.

Disposal instructions

To minimize pollution

and ensure utmost protection of the global environment

, dispose of

this product only in accordance with local, state, or Federal regulations for the disposal of

electronic waste.

Содержание 21824



































Результаты поиска

Содержание 21824

Отзывы:

Похожие инструкции для 21824

Бренды по названию

Популярные бренды

Monoprice 21824, Руководство пользователя

Результаты поиска

Содержание 21824

Отзывы:

Похожие инструкции для 21824

Бренды по названию

Популярные бренды