background image

CUSTOMIZATION BASICS: 
Framed Or Overlay Panels, Custom Handles and Accessory Kits

Overlay panels
You may also choose to install custom overlay panels
from your cabinet manufacturer. This design provides 
a seamless appearance which integrates smoothly with
surrounding cabinetry. 

Standard supplied handles shown in 19 mm overlay panel position.

Professional Style Stainless Steel Refrigerators
Stainless steel wrapped refrigerators have beveled edges
and professional-style handles. These models are shipped
ready for installation.

Trimmed Refrigerators
Trimmed refrigerators are designed to be customized 
with decorative panels. Field installed custom door 
and grille panels are required.

Framed panels
You may install 6 mm-thick custom panels from 
your cabinet manufacturer. The decorative panel slides
into the factory installed trim. Order black or stainless steel
accessory panels from your Monogram dealer. 

6

Standard supplied handles shown in 6 mm panel position.

Door Handles
The standard supplied handles can be adjusted to
accommodate both framed or overlay panels. Custom
handles of your choice, supplied by your cabinetmaker
can also be installed on 19 mm overlay panels. If desired, 
you may order ZKHSS2 Monogram stainless steel 
tubular handle kit for 19 mm overlay panels.

Side Panels 
Side panels must be used whenever the sides 
of the refrigerator will be exposed.

Optional Accessory Kits
ZKHSS2: Monogram tubular stainless steel handles
designed to fit 19 mm overlay panels.

Accessory Panels
Black and stainless steel accessory panels are available
from your Monogram dealer. Panels are cut to size and
ready to install. 

Black

Models

Acrylic

ZISB480D

ZPB480D

ZIS480N

ZPB480N

ZISB420D

ZPB420D

ZIS420N

ZPB420N

Framed Panel

Standard Door Handles

Design Guide

19 mm Overlay Panel

3 mm Thick Spacer Panel

6 mm Thick Backer Panel

Standard Door Handles

Содержание ZIS420N

























Отзывы: