3/4" OVERLAY PANEL DIMENSIONS
For a more custom appearance, overlay panels may be
installed on trimmed models. The overlay panel must
be secured to a 1/4" thick backer panel which slides
into the trim. A spacer panel 0.10" thick must be placed
between the overlay and backer panel.
Assemble the panels with glue and screws.
• Center the spacer panel on the backer panel, left to
right and top to bottom. Secure the panels with glue.
• Center the spacer and backer panel on the overlay
panel and secure with glue and screws. Screws must be
countersunk into the backer panel.
NOTE:
Left-to-right offset
is not always equal to
top-to-bottom offset.
8
Design Guide
Spacer Panel
Overlay Panel
Backer Panel
Fresh Food
Panel
Freezer
Panel
E
D
F
G
A
B
Grille Panel
C
Dispenser
Cutout
9-5/8"
Dispenser Cutout
15-3/8"
*Cut the dispenser opening after the backer, spacer and overlay
panels have been assembled.
36”
Side-by-Side (in inches)
A
B
C
D
E
F
G
1/4” Backer Panel
33-7/8
9
68-3/8
14-9/16
18-9/16
.10” Spacer Panel
33
8-3/8
67
13-1/4
17-1/4
3/4" Overlay Panel
34-1/8
9-1/4
68-5/8
14-13/16
18-13/16
17-15/16
3-1/4
42” Side-by-Side (in inches)
A
B
C
D
E
F
G
1/4” Backer Panel
39-7/8
9-1/2
68-3/8
14-9/16
24-9/16
.10” Spacer Panel
39
8-5/8
67
13-1/4
23-1/4
3/4" Overlay Panel
40-1/8
9-3/4
68-5/8
14-13/16
24-13/16
17-15/16
3-1/4
48” Side-by-Side (in inches)
A
B
C
D
E
F
G
1/4” Backer Panel
45-7/8
9-1/2
68-3/8
18-9/16
26-9/16
.10” Spacer Panel
45
8-5/8
67
17-1/4
25-1/4
3/4" Overlay Panel
46-1/8
9-3/4
68-5/8
18-13/16
26-13/16
17-15/16
5-1/4
*Dispenser
Cutout Position
IMPORTANT NOTE:
Maximum
total weight for assembled fresh
food panel is 50 pounds and 30
pounds for freezer panel.
IMPORTANT NOTE – Dispenser Models
The refrigerator is supplied with two dispenser trims,
one for framed panels and one for overlay panels.
The overlay dispenser trim is designed to fit a total
panel thickness of 1.100".
• If the panel is less than 1.100" a noticeable gap may
be created around the dispenser trim.
• If the panel is more than 1.100" the dispenser trim
cannot be secured to the door.
See Dispenser Trim Fit Example, page 9.
.250" + .10" + .750" = 1.100" Total Panel Thickness
• The overlay panel must be constructed according to
the specifications shown to achieve the correct total
thickness.
• Alternative panel construction methods such as
securing a 3/4" panel to a 1/4" backer panel cannot
be used. Another method, routing a 3/4" thick panel
on all sides cannot be used. These methods will not
result in the required 1.100" panel thickness.
When a raised panel design is to be used, a custom
middle rail is required. See page 9 for details.
3/4"
Overlay
Panel
1/4"
Backer
Panel
Door
.10"
Spacer
Содержание ZIS360N
Страница 19: ...19 Notes ...
