Monogram ZIFS360NHLH Скачать руководство пользователя страница 34

Installation Instructions - Flush Installation

34

Remove Grilles for Access to Anti-Tip Locking Hooks
Fresh Food Unit
• Open the access door.
• Remove the 4 screws from the grille.
• Pull the bottom of the grille forward, down and out to 

remove.

Freezer Unit
• Open the access door.
• Remove the 4 screws from the grille.
• Pull the bottom of the grille forward, down and out to 

remove.

Power Cord

Locate the power cord inside the left cavity. If it has not 
been adjusted so the plug is easily accessible, do so now.

Move Unit into Final Position
• Move appliance toward its final installed location. Align 

the tabs on the wall bracket with the openings in the back 
of the unit. 

• The unit has “L” bolts in the upper left and right corners 

inside of the access compartment. These bolts will 
interlock with the wall bracket and secure the unit using 
the washers and hair pin cotters in the hardware kit once 
the unit has been leveled and is in the final position. 

 STEP 5   INSTALL ANTI-TIP BRACKET (cont.) 

 STEP 6  LEVEL UNIT

All models have 4-point leveling. The front is supported by 

leveling legs; the rear is supported by adjustable wheels. 

Both are accessible from the front of the unit.
• To level the back of the unit, turn the 7/16” hex nut 

located above the front wheels. Turn clockwise to raise or 

counterclockwise to lower the unit.

• For front leveling, use a 1-1/4” open-end wrench.
• Adjust height of unit to match installation cutout 

opening 84-1/2”. The unit should be level and plumb with 

cabinetry.

NOTE: Raise 

appliance 

until the case 

top comes in 

contact with 

the 1” spacer 

block mounted 

to the underside 

of the cabinet 

soffit. Appliance 

should be level 

at fully raised 

position.

CAUTION

 

The rear leveling wheels and front leveling legs are limited 

to a maximum height adjustment of 1”. If the installation 

requires more than 84-1/2” height, the installer should 

elevate the unit on a sheet of plywood or runners. Cabinetry 

trim could also be added across the top of the opening to 

shorten the opening. If you attempt to raise the unit more 

than 1”, you will damage the front leveling legs and the rear 

leveling wheels.

ATTENTION

Les roues de nivellement arrière et les pattes de nivellement 

avant permettent un réglage maximal de 25 mm (1 po). 

Si l’ouverture pour l’appareil ménager a une hauteur 

supérieure à 2,15 m (84-1/2 po), l’installateur doit élever 

l’appareil ménager sur une feuille de contre-plaqué ou des 

glissières. Il est également possible d’ajouter des baguettes 

de finition des placards sur le haut de l’ouverture afin de la 

réduire. Lever l’appareil ménager de plus de 25 mm (1 po) 

endommage les pattes de nivellement avant et les roues de 

nivellement arrière.

Содержание ZIFS360NHLH





















































Отзывы: