Monicon GTR-85 Скачать руководство пользователя

Страница: 3 / 32

1 Introduction

1.1 GTR-85 Panel

1.1.1 Indicators

Power

Run

Stop

Trip

Alarm

Over

Crank

High

Water

Temp.

Over

Speed

Low Oil Pressure

1.1.2 Rotary

Switch

Function

Network

Allow online authorized user entry to perform
monitoring and control.

ATS

The engine starts automatically, when shorted
ATS1 and ATS2 terminal behind the controller
under ATS mode.

Manual

User starts the engine directly.

Off

Shutdown the engine or forbid start function.

1.1.3 Push-Butt

on Function

PAGE

Change LCD display page for reading more
information.

Light

Test

Test lights for solid, clear and brightness. It also tests
alarm.

Reset

1. First time “Reset” shutdown the alarm.

Second time “Reset” clears fault lights.

2. Holding down for a longer period will produce

1st and 2nd time “Reset” functions.

3. Turn on the LCD backlight.

Figure 1 – GTR85 Panel

Содержание GTR-85

































Результаты поиска

Содержание GTR-85

Отзывы:

Похожие инструкции для GTR-85

Бренды по названию

Популярные бренды

Monicon GTR-85, Руководство пользователя

Результаты поиска

Содержание GTR-85

Отзывы:

Похожие инструкции для GTR-85

Бренды по названию

Популярные бренды