manualshive.com logo in svg

Monarch 9416 XL, Быстрая справка

Поделиться
Скачать
Monarch 9416 XL Скачать руководство пользователя страница 1

MONARCH® 9416® XL®  
QUICK REFERENCE 

This 

Quick Reference

 contains ribbon loading, supply loading, and 

general care, maintenance, and troubleshooting procedures for the 
9416® XL® Thermal Direct and 9416® XL® Thermal Transfer 
printers.  For more detailed information, refer to the 

Equipment 

Manual

 on our Web site (

www.monarch.com

). 

Connecting the Power Supply 

1. 

Turn off the printer.  Press the switch on the back of the printer 
to the OFF position (O). 

2. 

Plug the three-hole end of the AC adapter cable into the three-
pronged outlet in the power supply. 

3. 

Plug the round end of the power supply cable (labeled “printer”) 
into the socket at the back of the printer. 

4. 

Plug the three-pronged end of the AC adapter cable into a 
grounded electrical outlet. 

Warning:   

The printer and power supply should never be 
operated in a location where either one can get wet.  
Personal injury could result.

  

 
 

TC9416QR  Rev. AJ  10/09  

2003 Avery Dennison Corp.  All rights reserved. 

Содержание 9416 XL























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды