background image

Please note: On your guarantee card there is a section that asks you ‘Drops’?
Please note that this question does NOT apply to the Plumbsoft models.

IMPORTANT

It is important that the softener is kept full of either tablet or block salt at all 
times. This goes in the chamber under the curved lid at the front of the machine
for Solo models and under the Blue lid for Premio models.

7

Insert pin fully ensuring it goes through both top and 

bottom of bracket/clamp

Unit with ¾” bypass fully connected.

Note: Protruding male vertical piece on top of blender valve 

is for setting 60/70ppm water hardness if required 

L: BLENDING CONTROL

– see 

STEP BY STEP GUIDE TO CONNECT THE BYPASS CONNECTION

Fig 4

Grease all 4 ‘o’ rings as shown on bypass above.

Fig 5     

           Fig 6

Insert bypass into softener connection ports complete with 

bracket/clamp attached.

Insert pin into bracket/clamp hole

Fig 7

Fig 8

M. STEP BY STEP GUIDE TO CONNECT THE PREMIO BYPASS

 CONNECTION

Please note: On your guarantee card there is a section that asks you ‘Drops’?
Please note that this question does NOT apply to the Plumbsoft models.

IMPORTANT

It is important that the softener is kept full of either tablet or block salt at all 
times. This goes in the chamber under the curved lid at the front of the machine
for Solo models and under the Blue lid for Premio models.

7

Insert pin fully ensuring it goes through both top and 

bottom of bracket/clamp

Unit with ¾” bypass fully connected.

Note: Protruding male vertical piece on top of blender valve 

is for setting 60/70ppm water hardness if required 

L: BLENDING CONTROL

– see 

STEP BY STEP GUIDE TO CONNECT THE BYPASS CONNECTION

Fig 3

Inlet and Outlet connections clearly marked on the softener.

Grease inside of connection ports prior to inserting bypass.

Fig 5     

           Fig 6

Insert bypass into softener connection ports complete with 

bracket/clamp attached.

Insert pin into bracket/clamp hole

Fig 7

Fig 8

M. STEP BY STEP GUIDE TO CONNECT THE PREMIO BYPASS

 CONNECTION

Please note: On your guarantee card there is a section that asks you ‘Drops’?
Please note that this question does NOT apply to the Plumbsoft models.

IMPORTANT

It is important that the softener is kept full of either tablet or block salt at all 
times. This goes in the chamber under the curved lid at the front of the machine
for Solo models and under the Blue lid for Premio models.

7

Insert pin fully ensuring it goes through both top and 

bottom of bracket/clamp

Unit with ¾” bypass fully connected.

Note: Protruding male vertical piece on top of blender valve 

is for setting 60/70ppm water hardness if required 

L: BLENDING CONTROL

– see 

STEP BY STEP GUIDE TO CONNECT THE BYPASS CONNECTION

Fig 3

Fig 4

Inlet and Outlet connections clearly marked on the softener.

Grease all 4 ‘o’ rings as shown on bypass above.

Insert pin into bracket/clamp hole

Fig 7

Fig 8

M. STEP BY STEP GUIDE TO CONNECT THE PREMIO BYPASS

 CONNECTION

Please note: On your guarantee card there is a section that asks you ‘Drops’?
Please note that this question does NOT apply to the Plumbsoft models.

IMPORTANT

It is important that the softener is kept full of either tablet or block salt at all 
times. This goes in the chamber under the curved lid at the front of the machine
for Solo models and under the Blue lid for Premio models.

7

Insert pin fully ensuring it goes through both top and 

bottom of bracket/clamp

Unit with ¾” bypass fully connected.

Note: Protruding male vertical piece on top of blender valve 

is for setting 60/70ppm water hardness if required 

L: BLENDING CONTROL

– see 

STEP BY STEP GUIDE TO CONNECT THE BYPASS CONNECTION

Fig 3

Fig 4

Inlet and Outlet connections clearly marked on the softener.

Grease inside of connection ports prior to inserting bypass.

Grease all 4 ‘o’ rings as shown on bypass above.

Fig 5     

Insert bypass into softener connection ports complete with 

bracket/clamp attached.

Fig 7

Fig 8

M. STEP BY STEP GUIDE TO CONNECT THE PREMIO BYPASS

 CONNECTION

Please note: On your guarantee card there is a section that asks you ‘Drops’?
Please note that this question does NOT apply to the Plumbsoft models.

IMPORTANT

It is important that the softener is kept full of either tablet or block salt at all 
times. This goes in the chamber under the curved lid at the front of the machine
for Solo models and under the Blue lid for Premio models.

7

Unit with ¾” bypass fully connected.

Note: Protruding male vertical piece on top of blender valve 

is for setting 60/70ppm water hardness if required 

L: BLENDING CONTROL

– see 

STEP BY STEP GUIDE TO CONNECT THE BYPASS CONNECTION

Fig 3

Fig 4

Inlet and Outlet connections clearly marked on the softener.

Grease inside of connection ports prior to inserting bypass.

Grease all 4 ‘o’ rings as shown on bypass above.

Fig 5     

           Fig 6

Insert bypass into softener connection ports complete with 

Insert pin into bracket/clamp hole

Fig 8

M. STEP BY STEP GUIDE TO CONNECT THE PREMIO BYPASS

 CONNECTION

Please note: On your guarantee card there is a section that asks you ‘Drops’?
Please note that this question does NOT apply to the Plumbsoft models.

IMPORTANT

It is important that the softener is kept full of either tablet or block salt at all 
times. This goes in the chamber under the curved lid at the front of the machine
for Solo models and under the Blue lid for Premio models.

7

Insert pin fully ensuring it goes through both top and 

bottom of bracket/clamp

is for setting 60/70ppm water hardness if required 

L: BLENDING CONTROL

– see 

STEP BY STEP GUIDE TO CONNECT THE BYPASS CONNECTION

Fig 3

Fig 4

Inlet and Outlet connections clearly marked on the softener.

Grease inside of connection ports prior to inserting bypass.

Grease all 4 ‘o’ rings as shown on bypass above.

Fig 5     

           Fig 6

Insert bypass into softener connection ports complete with 

bracket/clamp attached.

Insert pin into bracket/clamp hole

Fig 7

M. STEP BY STEP GUIDE TO CONNECT THE PREMIO BYPASS

 CONNECTION

Air Check 

Supplied tubing 
connection (8cm) 

Remove the small grey clip from 

the air check connector.

Remove the connector and rotate 

180 degrees.

Using the supplied fittings and tubing 

(8cm), attach the air check to the valve, 

using the push-fit connector and 

placing the blue clip back on (as 

pictured).

Air check connector

15

Содержание PREMIO HE





















Отзывы: