background image

2

2.

Laser On

 

LED

Blinks when unit is first turned on.  Remains
lit when the laser beam is on.

3.

Auto/Gain

 

LED

On solid whenever the unit is in the Auto
mode.  It also blinks from 1 to 8 times to
indicate the current gain whenever the gain is
changed.

4.

Power LED

(Dependent on the Power switch location)

On position:

GREEN when the batteries are charged.

Blinks AMBER when the batteries are low.

Charge position:

Blinks RED when fast charging for very low
batteries.

Blinks AMBER when slow charging.

Steady AMBER when the batteries are fully
charged.

5.

Polarity switch

Selects either a positive or negative output
pulse.

6.

Learn/Gain button

In Auto Mode:

Press and hold until the On Target LED blinks
regularly or is on solid.

In Manual Mode: Press to change gain ranges.

7.

Sensitivity Adjust knob

Turn fully counterclockwise to select
Auto mode or manually adjust
sensitivity threshold.

8.

Power switch

Turns unit On or Off.  When the unit is
switched to Off/Charge and a charger is
plugged into the unit, the batteries will charge.

9

9.0 CHARGING

Slide the Power switch (8) to the 

Off/Charge

 position and plug in the

charger.  The 

Power

 LED (4) will blink red while the unit is fast charging.

The 

Power

 LED will blink amber when slow (trickle) charging.  It will be

solid amber when the batteries are fully charged.

Note:

If the charger is plugged in when the Power switch is the on
position, the batteries will be trickle charged during operation.

CAUTION:

Use only the supplied PR-Universal charger with the
sensor.

10.0 SMART LASER SENSOR SPECIFICATIONS

Laser Specifications:

Classification:

Class 3R (per IEC 60825-1 Ed 1.2 2001-8)

Complies with FDA performance standards for laser products except for
deviations pursuant to Laser Notice No. 50, dated July 26, 2001.

Maximum Laser Output:

3mW

Pulse Duration:

Continuous

Laser Wavelength:

650 nm

Beam Divergence:

< 0.5 mrad

Beam Diameter:

4 x 7 mm typical at 2 meters

Laser Diode Life:

8,000 hours MTBF (1 year warranty)

AVOID EXPOSURE
LASER RADIATION IS
EMITTED FROM THIS
APERTURE.

 

Laser is on when this
indicator is illuminated.

www.calcert.com

[email protected]

1.800.544.2843

0

5

10

15

20

25

30

Содержание 6180-012

















Отзывы: