9
normal and does not indicat e a problem.
•
Do not place t he charger and bat t ery pack in an
area of ext reme heat or cold. They will work best
at normal room t emperat ure.
NOTICE:
The charger and bat t ery pack should be
placed in a locat ion where t he t emperat ure is
more t han 32
°
F but less t han 100
°
F.
•
When bat t eries become fully charged, unplug t he
charger from power supply and remove t he
bat t ery pack.
CHARGING A HOT BATTERY PACK
When using t he t ool cont inuously, t he bat t eries in
t he bat t ery pack will become hot . You should let a
hot bat t ery pack cool down for approximat ely 30
minut es before at t empt ing t o recharge. When t he
bat t ery pack becomes discharged and is hot , t his will
cause t he green LED t o come on inst ead of t he red
LED. Aft er 30 minut es, reinsert t he bat t ery pack in
t he charger. If t he green LED cont inues t o remain on,
ret urn bat t ery pack t o your nearest M okeneye
Aut horized Service Cent er for checking or replacing.
NOTICE:
This sit uat ion only occurs when cont inuous
use of t he t ool causes t he bat t eries t o become hot . It
does not occur under normal circumst ances. Refer t o
"CHARGING A COOL BATTERY PACK"
for normal
recharging of bat t eries. If t he charger does not
charge
your
bat t ery
pack
under
normal
circumst ances, ret urn bot h t he bat t ery pack and
charger t o your nearest M okeneye Aut horized
Service Cent er for elect rical check.
TO ATTACH/DETACH BATTERY PACK
Fig. 2
Battery tools are alw ays in
operating condition. Therefore,
remove the battery w hen assembling parts,
making adjustments, cleaning, w hen the tool is
not in use, or w hen carrying it at your side.
Removing the battery pack w ill prevent
accidental starting that could cause serious
personal injury.
To attach the battery pack:
•
Align t he ribs of t he bat t ery pack w it h t he
mount ing slot s in t he blow er's bat t ery port .
•
Press t he bat t ery pack t ow ard t he blow er body
unt il it snaps int o posit ion.
NOTICE:
M ake sure t hat t he bat t ery pack is
secured t o t he blow er before beginning operat ion.
NOTICE:
When placing t he bat t ery pack ont o t he
t ool, be sure t hat t he raised rib on t he bat t ery pack
aligns w it h t he groove inside t he t ool and t hat t he
lat ches snap int o place properly. Improper
at t achment of t he bat t ery pack can cause damage
t o int ernal component s.
To detach the battery pack:
Depress t he bat t ery-release but t on locat ed on t he
front of t he bat t ery pack t o release t he bat t ery
pack. Pull t he bat t ery pack out and remove it from
t he t ool.
TO ASSEMBLE THE BLOWER TUBE
Fig. 3
a. Short pipe connection
To clean up t he w orkbench, just connect t he front
blow pipe.
•
Align t he knobs inside t he front t ube w it h t he
grooves in t he blow er housing. Push t he t ube
ont o t he blow er housing and rot at e clockw ise
unt il it snaps int o place (Fig. 3a). Pull on t he t ube
t o ensure t hat it is securely at t ached t o t he
blow er.
b. Extension tube connection
An ext ension t ube can be inst alled for ground blow
w ork.
•
Align t he knobs inside t he front t ube w it h t he
grooves in t he ext ension t ube. Push t he front
t ube ont o t he ext ension pipe and rot at e
clockw ise unt il it snaps int o place (Fig. 3b). Pull
on t he front t ube t o ensure t hat it is securely
at t ached t o t he ext ension t ube.
•
Align t he knobs inside t he ext ension t ube w it h
t he grooves in t he blow er housing. Push t he t ube
ont o t he blow er housing and rot at e clockw ise
unt il it snaps int o place (Fig. 3c). Pull on t he t ube
t o ensure t hat it is securely at t ached t o t he
blow er.
TO ASSEMBLE THE SUCTION FITTINGS
Fig. 4
Using t he negat ive pressure, t his t ool can complet e
t he vacuuming w ork only by changing t he posit ion of
t he t ube, t he blow er housing, t he front t ube and t he
combinat ion of t he collect ion bag.
•
Align t he knobs inside t he short t ube in front of
dust bag w it h t he grooves in t he air out let at t he
front of t he blow er housing. Push t he bag ont o
t he blow er housing and rot at e clockw ise unt il it
snaps int o place (Fig. 4a). Pull on t he bag t o
ensure t hat it is securely at t ached t o t he blow er.
•
Align t he knobs inside t he front t ube w it h t he
grooves in t he air inlet on t he side of t he fan. Push
t he front t ube ont o t he blow er and rot at e
clockw ise unt il it snaps int o place (Fig. 4b). Pull on
t he front t ube t o ensure t hat it is securely
at t ached t o t he blow er.
VARIABLE-SPEED TRIGGER SWITCH
Fig. 5
NOTICE:
Before pulling t he t rigger t o st art t he
blow er, ensure t hat it is not in cont act w it h any
object .
•
Your t ool is equipped w it h a variable-speed
t rigger sw it ch. The variable-speed t rigger sw it ch
delivers higher speed w it h increased t rigger
pressure and low er speed w it h decreased t rigger
pressure.
•
The t rigger dept h limit depends on t he speed dial
scale.
Alw ays remove the blow er during
w ork breaks and after finishing
w ork.
