Modulus Arms Heavy-Duty Universal AR-15 80% Jig Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 21

Modulus Arms Heavy-Duty Universal AR-15 80% Jig Скачать руководство пользователя страница 7

www.ModulusArms.com

January 14, 2016

www.ModulusArms.com | Heavy-Duty Universal AR-15 80% Jig Instructions

7

Side Plates

: Place the Left Side Plate into position and thread two ½” screws into the top through the

Top Plate as shown in Figure 7.  Repeat for the Right Side Plate. Leave these four screws loose. Squeeze
the side plates together against the sides of the lower receiver. When they are tight to the lower
receiver, tighten the four ½” screws to 1 ft-lb. Screw the 8-32 x  1.5” Side Plate Support Screw into the
Right Side Plate and all the way through into the Left Side Plate as shown in Figure 8. Tighten to 1 ft-lb.
Do not install the ¼-20 x 1.5” Rear Takedown Screw.



Note

: Many questions have been asked about the Side Plate Support Screw. It is used to prevent

the side plates from flexing in when clamped in a vise. That is why both sides are threaded.



Note

: It is recommended to put masking tape or some other protection over the sides of the

lower before installing the side plates. Doing so will help prevent scratches or wear.

Figure 7: Side Plate Screws

Figure 8: Support Screw Location

Leave Loose

Left Side Plate

Screws

Right Side Plate

Screws

Side Plate Support Screw

DO NOT INSTALL

«
...
5
6
7
8
9
...
»

Содержание Heavy-Duty Universal AR-15 80% Jig






















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды