MODULARWALLS Slimwall Classic Post Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 36

background image

SlimWall retaining can be simplified into four easy steps:

STEP 1 -

Set out your SlimWall as you would for a normal installation.

STEP 2 -

Any post that will be used for retaining needs to have reinforcing sleeves incorporated when the posts

are being screwed together. These are supplied as a part of your material kit and detailed further in this

guide.

STEP 3 -

Install the SlimWall Retaining Panel for the retaining sections of your SlimWall, using the supplied

stainless steel base channel.

STEP 4 -

Seal the retaining panels and backfill as specified.

SLIMWALL RETAINING PANEL

At times, a difference in ground levels can occur on opposite sides of a SlimWall installation. The SlimWall

Retaining Panel modular has been designed for use in these circumstances, providing a seamless appearence

whilst reliably holding these sil loads at bay. The SlimWall Retaining Panel provides a solution to backyard soil

retention up to 500mm (2.5 kPa) that is robust and elegant.

APPLICATION

SlimWall integrated with SlimWall Retaining Panel is ideally suited for:
- Replacement of an old timber or colorbond fence that is leaning away from the retained embakment
- New housing developments or subdivisions with uneven ground levels between blocks
- Stand-alone planter boxes, raised garden beds or terraced lawns

SPECIFICATION

The SlimWall Retaining Panel consists of:
- Fibre cement outer skins
- High density EPS core
- internal reinforcing ribs
- Size: 2400mm (L) x 600mm (H) x 50mm (W)

ADDITIONAL

SLIMWALL™ RETAINING PANEL

SLIMWALL™ INSTALLATION GUIDE

25

«
...
23
24
25
26
27
...
»

Содержание Slimwall Classic Post





































Отзывы:

Нет отзывов

Похожие инструкции для Slimwall Classic Post

Бренд: PF Страницы: 34

Бренд: Safetots Страницы: 4

Бренд: LEGI Страницы: 4

Бренд: Kerbl Страницы: 4

240mm Rigidline

Бренд: straightcurve Страницы: 2

Бренд: Zippity Страницы: 17

Бренд: Power Wizard Страницы: 16

Бренд: Ares Страницы: 26

MONTAGE Classic

Бренд: Ameristar Страницы: 4

Бренд: Ameristar Страницы: 7

Бренд: Ameristar Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды