Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
To maintain compliance with FCC RF exposure compliance requirements, please avoid direct contact to
the transmitting antenna during transmitting.
RF Exposure Warning!
This device contains transmitters and receivers which emit Radio Frequency (RF) energy. The device
is designed to comply with the limits for exposure to RF energy set by the Federal Communications
Commission (FCC) of the United States, Industry Canada (IC) of Canada, and the regulating entities
of other countries.
BTH-600-ZU-MOB
Wireless Bluetooth Speaker Microphone
For use with Zello on Android smartphones
If you are still concerned about exposure to RF energy,
you can further limit your exposure by limiting the
amount of time you use the equipment or by placing
more distance between your body and the device,
since exposure level drops off dramatically
with distance.
911 Mariner St., Brea, CA 92821
PH: 714.257.0300 FAX: 714.257.0600
PRYME® and PRYMEBLU® are trademarks owned by PRYME Radio Products,
Model No. BTH-600-MOB
Made in Taiwan
TOLL FREE: 800.666.2654
2
Brea CA. All other product or service names are the property of their respective owners.
© 2018 PRYME Radio Products, Brea CA. All Rights Reserved
Controls and Connection
Front Firing Speaker
Received calls are heard over this speaker.
The volume level can be controlled using
either the Volume Up / Down buttons on
the speaker microphone, or by using the
volume controls on the phone.
PTT Button
This button is used to activate the
push-to-talk feature of the Zello app.
Microphone
This microphone picks up the user’s
voice audio when sending a call
Volume Up and Down Buttons
These buttons can be used to turn
the receive audio volume of the
speaker microphone up or down
in five preset steps
Bulkhead Connector
Used to connect the extension
cable to the microphone
Mic Hangar Knob
The mobile-radio style mic hangar
secures the speaker microphone inside
the hangar bracket
Phone Button
This button can be
used to answer or
hang up phone calls.
Status LEDs
The red and blue LEDs flash
messages that let the user
know the current status of
the speaker microphone.
Pairing Button
Holding down this button for three
seconds will place the speaker microphone
into pairing mode so that it can be connected
wirelessy to a cellualr phone or tablet.
3.5
mm Audio Jack
Used to connect the microphone
to a n optional external speaker
with a 3.5mm mono plug
NOTE:
The BTH-600_ZU-MOB
speaker microphone is powered
by an ex5V source within
the vehicle. The microphone
operatess in an "always on"
mode as long as power is being
supplied. In most applications,
it is recommended to tie the
external USB power source to
vehicle ignition, so that the
microphone will automatically
power on and off with the vehicle.
Mic Hangar Brackey
Allows the microphone to be hung up
during use. Includes two screws for
mounting.
Microphone Connector
Used to connect the microphone to the supplied
power supply or an optional extension cable
USB-A Connector
Used to connect the microphone
to a powered USB (+5V DC) source
3
4
Mobility Sound Technology Ltd.
5F, No.100, Jian 1
st
Road, ZhongHe Dist.
New Taipei City 23585, Taiwan
Tel: (886) 2 2223-2377 Fax: (886) 2 2223-1968
