Mobeye PowerGuard CM2100 Скачать руководство пользователя страница 2

 

 

Attention! Very important 

 
This user manual contains important guidelines for the installation and usage of the Mobeye

® 

device 

as described in this manual. Please read these thoroughly before you start using the Mobeye

® 

device! 

In case of damage caused by disregarding the guidelines, the warranty expires.  
The user must regularly check the proper functioning of the device. The manufacturer cannot be held 
liable for any damage caused by any incorrect use or incorrect functioning of the Mobeye

® 

device. 

 
Safety guidelines 
•  The permitted ambient temperature during operation may not be exceeded (not lower than -10°C 

and not higher than 50°C). 

•  The device is intended for use in dry and clean places. 
•  Protect the device from moisture, heat and water splashing. 
•  The guidelines for the battery usage must be regarded.  
•  Do not expose the device to strong vibrations. 
•  Do not let it fall from height. 
•  Do not use in an environment where any inflammable gases, vapors or dust are present or could be 

present.  

•  The repairs of the device may only be carried out by people, trained for Mobeye

®

 repair. 

•  In case the device must be repaired, only original replacement components may be used. The use of 

different parts may lead to damage of the Mobeye

®

 device. 

 

Use in accordance with the regulation  

The use of this device in accordance with the regulation is sending SMS text messages and making 
telephone calls after an alarm situation. Other usages are not permitted. 
 

Battery recycling 

CR123 batteries, as used in the Mobeye PowerGuard, are classified as non-hazardous waste and can 
be recycled. Please take empty batteries to a nearest collection point.

 

Содержание PowerGuard CM2100















Отзывы: