Mobeye PowerGuard CM2100 Скачать руководство пользователя страница 13

11 

 

6. TECHNICAL MESSAGES AND STATUS FEEDBACK 

 

Technical messages 

 
In case of a technical problem, the administrator receives an SMS message. Possible technical 
messages are: 
 

Message  

Reason  

Low batteries, external power supply 
OK 

Power is available, batteries need to be replaced 

No external power supply, batteries OK  No external power supply, batteries are capable to 

take over operation in low power mode 

Low batteries, no external power 
supply 

No external power supply, batteries need to be 
replaced 

External power supply OK, batteries 
OK 

The external power is restored (or the adapter is 
plugged in a socket), batteries do not need to be 
replaced 

Message(s) missed due to 
Network/SIM failure 

One  or  more  SMS  text  messages  couldn’t  be  sent, 
due to a SIM card failure or GSM network failure.  

 
When receiving one of the above mentioned technical messages, please take appropriate action 
as soon as possible. During the battery replacement, the SIM card does not have to be removed.  

 
Status feedback 
 

Status 

LED pattern 

Required action 

Module not configured 

Blinking 1 second on / 1 
second off 

Configure at least one telephone 
number  

Module is switched on, 
powered by batteries 

1 flash every 3 seconds 

No action required 

Module is switched on, 
powered by an external source 

On 

No action required 

Module establishes network 
connection to send an alarm 
message 

Blinking 2 seconds on, 1 
second off  

Wait until the network connection 
is established and the message 
is sent 

Module establishes network 
connection to get to program 
mode 

Blinking 3 seconds on, 1 
second off  

Wait until the network connection 
is established before 
programming  

No GSM connection 

2 flashes every 3 seconds  Try the SIM card in any mobile 

telephone; replace SIM card 
using other telecom provider; try 
the module at another location  

No valid SIM card or wrong PIN  3 flashes every 3 seconds  Try the SIM card in any mobile 

telephone; remove PIN code; 
check credit; replace SIM card 

Successful programming action  Blinking 3 times 

No action required 

Faulty programming action 

Flashing 5 times 

Check SMS command 

Low batteries 

4 flashes every 3 seconds  Replace both batteries 

 
 

 
 

 

Содержание PowerGuard CM2100















Отзывы: