MME Motorsport GCU7 Скачать руководство пользователя

Страница: 7 / 33

2020-08-26

GCU7 Manual

GENERAL/SENSORS

Please note: if any parameter is changed, settings must be sent to the GCU (Settings – send to GCU or
Send Changed to GCU - F5) in order to take effect.

GEARBOX

There are currently two types of gearboxes supported. Sequential & H-Paddle Shifter (Synchro /
Dogbox).

Gearbox Type:

Sequential

This is regular sequential gearbox with up/down movement. Only two valves (1 two way actuator) is
used in this configuration.

Gearbox type:

Type: H / Synchro or H / Gearboxes

H-Paddle is MME Motorsport actuator assembly that controls 8 valves and shifts any H pattern. For
more H-Paddle Shifter options see

H-Paddle Shifter actuators

Number of forward gears is in the

Number of gears

dropdown.

Mid neutral

If gearbox with neutral between the 1 and R is used (like Sadev ST75), this option is used to allow the
GCU to shift only partially. See

MISC/LOGGING

for setting up the neutral.

Содержание GCU7


































Результаты поиска

Содержание GCU7

Отзывы:

Похожие инструкции для GCU7

Бренды по названию

Популярные бренды

MME Motorsport GCU7, Руководство пользователя

Результаты поиска

Содержание GCU7

Отзывы:

Похожие инструкции для GCU7

Бренды по названию

Популярные бренды