ll
ll
ll
ll ll ll ll
ll
ll
ll
ll
ll
Press to check the sensitivity settings are correct. The fitting will illuminate for 2
seconds when motion is detected. The standby period and daylight sensor are
disabled. Press “AUTO” to quit this mode
The sensor will automatically go into test mode after confirming selected
parameters
Daylight sensor mode. When the ambient light level exceeds the set lux level,
the luminaire will monitor for 1 minute to confirm the light level increase is not
temporary, and then turn off even when motion is detected. When the ambient
light level drops below the set lux level, the luminaire will turn on even without
motion detection after 1 minute. This feature is disabled by default - press to
activate and press again to deactivate
4 different modes can be saved. After selecting the desired parameters press a
mode button followed by “OK” to save the settings to that mode
Brightness
Adjust the brightness during hold time to: 70% / 80% / 90% / 100%
Sensitivity
Adjust the sensor sensitivity to: 20% / 50% / 75% / 100%
Hold time
Adjust the time period the luminaire remains at full brightness after no motion is
detected to: 10sec / 1min / 5min / 10min / 15min / 20min / 30min / 60min
Standby time
Adjust the time period the luminaire remains dimmed after the hold time to:
1m / 30m / 60m / +∞ When set to +∞ the luminaire will remain dimmed
permanently
Standby dim
Adjust the brightness during standby time to: 0% / 10% / 30% / 50%
Daylight
sensor
Press followed by either 10LUX / 30LUX / 50LUX / 100LUX / 300LUX
/ 500LUX then to adjust the setpoint at which the daylight sensor will operate
Press to select the current surrounding lux value as the daylight sensor
threshold
Press to disable the daylight sensor, the luminaire will switch on when motion
is detected regardless of the ambient light level
Confirm the selected parameters or save/confirm the selected mode
Reset to default settings: Brightness 100%, Sensitivity 100%, Hold time 5m,
Daylight mode, Standby dimming 30%, Standby dimming time 60m
Press to check the sensitivity settings are correct. The fitting will illuminate
for 2 seconds when motion is detected. The standby period and daylight
sensor are disabled. Press “AUTO” to quit this mode
The sensor will automatically go into test mode after confirming selected
parameters
Daylight sensor mode. When the ambient light level exceeds the set lux
level, the luminaire will monitor for 1 minute to confirm the light level
increase is not temporary, and then turn off even when motion is detected.
When the ambient light level drops below the set lux level, the luminaire will
turn on even without motion detection after 1 minute. This feature is
disabled by default - press to activate and press again to deactivate
Four different modes can be saved. After selecting the desired parameters
press a mode button followed by “OK” to save the settings to that mode
BRIGHTNESS
Adjust the brightness during hold time to: 70% / 80% / 90% / 100%
SENSITIVITY
Adjust the sensor sensitivity to: 20% / 50% / 75% / 100%
HOLD TIME
Adjust the time period the luminaire remains at 100% after no motion is
detected to: 10sec / 1min / 5min / 10min / 15min / 20min / 30min / 60min
STANDBY TIME
Adjust the time period the luminaire remains dimmed after the hold time to:
When set to + the luminaire will remain dimmed permanently
STANDBY DIM
Adjust the brightness during standby time to: 0% / 10% / 30% / 50%
DAYLIGHT
SENSOR
Press
followed by either 10LUX / 30LUX / 50LUX / 100LUX / 300LUX
/ 500LUX then
to adjust the setpoint at which the daylight sensor will
operate
Press
to select the current surrounding lux value as the daylight
sensor threshold
Confirm the selected parameters or save/confirm the selected mode
Reset to default settings: Brightness 100%, Sensitivity 100%, Hold time 5m,
Daylight mode, Standby dimming 30%, Standby dimming time 60m
Press to check the sensitivity settings are correct. The fitting will illuminate
for 2 seconds when motion is detected. The standby period and daylight
sensor are disabled. Press “AUTO” to quit this mode
The sensor will automatically go into test mode after confirming selected
parameters
Daylight sensor mode. When the ambient light level exceeds the set lux
level, the luminaire will monitor for 1 minute to confirm the light level
increase is not temporary, and then turn off even when motion is detected.
When the ambient light level drops below the set lux level, the luminaire will
turn on even without motion detection after 1 minute. This feature is
disabled by default - press to activate and press again to deactivate
Four different modes can be saved. After selecting the desired parameters
press a mode button followed by “OK” to save the settings to that mode
BRIGHTNESS
Adjust the brightness during hold time to: 70% / 80% / 90% / 100%
SENSITIVITY
Adjust the sensor sensitivity to: 20% / 50% / 75% / 100%
HOLD TIME
Adjust the time period the luminaire remains at 100% after no motion is
detected to: 10sec / 1min / 5min / 10min / 15min / 20min / 30min / 60min
STANDBY TIME
Adjust the time period the luminaire remains dimmed after the hold time to:
When set to + the luminaire will remain dimmed permanently
STANDBY DIM
Adjust the brightness during standby time to: 0% / 10% / 30% / 50%
DAYLIGHT
SENSOR
Press
followed by either 10LUX / 30LUX / 50LUX / 100LUX / 300LUX
/ 500LUX then
to adjust the setpoint at which the daylight sensor will
operate
Press
to select the current surrounding lux value as the daylight
sensor threshold
N
O
I
T
C
N
U
F
N
O
T
T
U
B
Press to switch between permanent on and permanent off. To quit this
mode press “AUTO”
Press to switch to sensor mode. All parameters revert to those last selected
Press to illuminate the current parameters selected on the remote
Press to upload the selected parameters to the sensor
Navigate up and down
Navigate left and right
Confirm the selected parameters or save/confirm the selected mode
Reset to default settings: Brightness 100%, Sensitivity 100%, Hold time 5m,
Daylight mode, Standby dimming 30%, Standby dimming time 60m
Press to check the sensitivity settings are correct. The fitting will illuminate
for 2 seconds when motion is detected. The standby period and daylight
sensor are disabled. Press “AUTO” to quit this mode
The sensor will automatically go into test mode after confirming selected
parameters
Daylight sensor mode. When the ambient light level exceeds the set lux
level, the luminaire will monitor for 1 minute to confirm the light level
increase is not temporary, and then turn off even when motion is detected.
When the ambient light level drops below the set lux level, the luminaire will
turn on even without motion detection after 1 minute. This feature is
disabled by default - press to activate and press again to deactivate
Four different modes can be saved. After selecting the desired parameters
press a mode button followed by “OK” to save the settings to that mode
BRIGHTNESS
Adjust the brightness during hold time to: 70% / 80% / 90% / 100%
SENSITIVITY
Adjust the sensor sensitivity to: 20% / 50% / 75% / 100%
HOLD TIME
Adjust the time period the luminaire remains at 100% after no motion is
detected to: 10sec / 1min / 5min / 10min / 15min / 20min / 30min / 60min
STANDBY TIME
Adjust the time period the luminaire remains dimmed after the hold time to:
When set to + the luminaire will remain dimmed permanently
STANDBY DIM
Adjust the brightness during standby time to: 0% / 10% / 30% / 50%
DAYLIGHT
SENSOR
Press
followed by either 10LUX / 30LUX / 50LUX / 100LUX / 300LUX
/ 500LUX then
to adjust the setpoint at which the daylight sensor will
operate
Press
to select the current surrounding lux value as the daylight
sensor threshold
N
O
I
T
C
N
U
F
N
O
T
T
U
B
Press to switch between permanent on and permanent off. To quit this
mode press “AUTO”
Press to switch to sensor mode. All parameters revert to those last selected
Press to illuminate the current parameters selected on the remote
Press to upload the selected parameters to the sensor
Navigate up and down
Navigate left and right
Confirm the selected parameters or save/confirm the selected mode
Reset to default settings: Brightness 100%, Sensitivity 100%, Hold time 5m,
Daylight mode, Standby dimming 30%, Standby dimming time 60m
Press to check the sensitivity settings are correct. The fitting will illuminate
for 2 seconds when motion is detected. The standby period and daylight
sensor are disabled. Press “AUTO” to quit this mode
The sensor will automatically go into test mode after confirming selected
parameters
Daylight sensor mode. When the ambient light level exceeds the set lux
level, the luminaire will monitor for 1 minute to confirm the light level
increase is not temporary, and then turn off even when motion is detected.
When the ambient light level drops below the set lux level, the luminaire will
turn on even without motion detection after 1 minute. This feature is
disabled by default - press to activate and press again to deactivate
Four different modes can be saved. After selecting the desired parameters
press a mode button followed by “OK” to save the settings to that mode
BRIGHTNESS
Adjust the brightness during hold time to: 70% / 80% / 90% / 100%
SENSITIVITY
Adjust the sensor sensitivity to: 20% / 50% / 75% / 100%
HOLD TIME
Adjust the time period the luminaire remains at 100% after no motion is
detected to: 10sec / 1min / 5min / 10min / 15min / 20min / 30min / 60min
STANDBY TIME
Adjust the time period the luminaire remains dimmed after the hold time to:
When set to + the luminaire will remain dimmed permanently
STANDBY DIM
Adjust the brightness during standby time to: 0% / 10% / 30% / 50%
DAYLIGHT
SENSOR
Press
followed by either 10LUX / 30LUX / 50LUX / 100LUX / 300LUX
/ 500LUX then
to adjust the setpoint at which the daylight sensor will
operate
Press
to select the current surrounding lux value as the daylight
sensor threshold
Reset to default settings: Brightness 100%, Sensitivity 100%, Hold time 5m,
Daylight mode, Standby dimming 30%, Standby dimming time 60m
Press to check the sensitivity settings are correct. The fitting will illuminate
for 2 seconds when motion is detected. The standby period and daylight
sensor are disabled. Press “AUTO” to quit this mode
The sensor will automatically go into test mode after confirming selected
parameters
Daylight sensor mode. When the ambient light level exceeds the set lux
level, the luminaire will monitor for 1 minute to confirm the light level
increase is not temporary, and then turn off even when motion is detected.
When the ambient light level drops below the set lux level, the luminaire will
turn on even without motion detection after 1 minute. This feature is
disabled by default - press to activate and press again to deactivate
Four different modes can be saved. After selecting the desired parameters
press a mode button followed by “OK” to save the settings to that mode
BRIGHTNESS
Adjust the brightness during hold time to: 70% / 80% / 90% / 100%
SENSITIVITY
Adjust the sensor sensitivity to: 20% / 50% / 75% / 100%
HOLD TIME
Adjust the time period the luminaire remains at 100% after no motion is
detected to: 10sec / 1min / 5min / 10min / 15min / 20min / 30min / 60min
STANDBY TIME
Adjust the time period the luminaire remains dimmed after the hold time to:
When set to + the luminaire will remain dimmed permanently
STANDBY DIM
Adjust the brightness during standby time to: 0% / 10% / 30% / 50%
DAYLIGHT
SENSOR
Press
followed by either 10LUX / 30LUX / 50LUX / 100LUX / 300LUX
/ 500LUX then
to adjust the setpoint at which the daylight sensor will
operate
Press
to select the current surrounding lux value as the daylight
sensor threshold
N
O
I
T
C
N
U
F
N
O
T
T
U
B
Press to switch between permanent on and permanent off. To quit this
mode press “AUTO”
Press to switch to sensor mode. All parameters revert to those last selected
Press to illuminate the current parameters selected on the remote
Press to upload the selected parameters to the sensor
Navigate up and down
Navigate left and right
Confirm the selected parameters or save/confirm the selected mode
Reset to default settings: Brightness 100%, Sensitivity 100%, Hold time 5m,
Daylight mode, Standby dimming 30%, Standby dimming time 60m
Press to check the sensitivity settings are correct. The fitting will illuminate
for 2 seconds when motion is detected. The standby period and daylight
sensor are disabled. Press “AUTO” to quit this mode
The sensor will automatically go into test mode after confirming selected
parameters
Daylight sensor mode. When the ambient light level exceeds the set lux
level, the luminaire will monitor for 1 minute to confirm the light level
increase is not temporary, and then turn off even when motion is detected.
When the ambient light level drops below the set lux level, the luminaire will
turn on even without motion detection after 1 minute. This feature is
disabled by default - press to activate and press again to deactivate
Four different modes can be saved. After selecting the desired parameters
press a mode button followed by “OK” to save the settings to that mode
BRIGHTNESS
Adjust the brightness during hold time to: 70% / 80% / 90% / 100%
SENSITIVITY
Adjust the sensor sensitivity to: 20% / 50% / 75% / 100%
HOLD TIME
Adjust the time period the luminaire remains at 100% after no motion is
detected to: 10sec / 1min / 5min / 10min / 15min / 20min / 30min / 60min
STANDBY TIME
Adjust the time period the luminaire remains dimmed after the hold time to:
When set to + the luminaire will remain dimmed permanently
STANDBY DIM
Adjust the brightness during standby time to: 0% / 10% / 30% / 50%
DAYLIGHT
SENSOR
Press
followed by either 10LUX / 30LUX / 50LUX / 100LUX / 300LUX
/ 500LUX then
to adjust the setpoint at which the daylight sensor will
operate
Press
to select the current surrounding lux value as the daylight
sensor threshold
N
O
I
T
C
N
U
F
N
O
T
T
U
B
Press to switch between permanent on and permanent off. To quit this
mode press “AUTO”
Press to switch to sensor mode. All parameters revert to those last selected
Press to illuminate the current parameters selected on the remote
Press to upload the selected parameters to the sensor
Navigate up and down
Navigate left and right
Confirm the selected parameters or save/confirm the selected mode
Reset to default settings: Brightness 100%, Sensitivity 100%, Hold time 5m,
Daylight mode, Standby dimming 30%, Standby dimming time 60m
Press to check the sensitivity settings are correct. The fitting will illuminate
for 2 seconds when motion is detected. The standby period and daylight
sensor are disabled. Press “AUTO” to quit this mode
The sensor will automatically go into test mode after confirming selected
parameters
Daylight sensor mode. When the ambient light level exceeds the set lux
level, the luminaire will monitor for 1 minute to confirm the light level
increase is not temporary, and then turn off even when motion is detected.
When the ambient light level drops below the set lux level, the luminaire will
turn on even without motion detection after 1 minute. This feature is
disabled by default - press to activate and press again to deactivate
Four different modes can be saved. After selecting the desired parameters
press a mode button followed by “OK” to save the settings to that mode
BRIGHTNESS
Adjust the brightness during hold time to: 70% / 80% / 90% / 100%
SENSITIVITY
Adjust the sensor sensitivity to: 20% / 50% / 75% / 100%
HOLD TIME
Adjust the time period the luminaire remains at 100% after no motion is
detected to: 10sec / 1min / 5min / 10min / 15min / 20min / 30min / 60min
STANDBY TIME
Adjust the time period the luminaire remains dimmed after the hold time to:
When set to + the luminaire will remain dimmed permanently
STANDBY DIM
Adjust the brightness during standby time to: 0% / 10% / 30% / 50%
DAYLIGHT
SENSOR
Press
followed by either 10LUX / 30LUX / 50LUX / 100LUX / 300LUX
/ 500LUX then
to adjust the setpoint at which the daylight sensor will
operate
Press
to select the current surrounding lux value as the daylight
sensor threshold
Содержание AX CCT
Страница 1: ...INSTALLATION MAINTENANCE MANUAL AXxxxCCT...
