MKS SM1690 Series Скачать руководство пользователя страница 12

Страница: 12 / 20

SM 1690

page 10 of 18

File: SM1690_r5eng - Dec. 2013 - Technical note: SM1690

SM 1690

SM 1280

SM 1690

File: SM1690_r5eng - Dec. 2013 - Technical note: SM1690

page 11 of 18

Internal settings

The SM1690x comes in the default settings with all

the SW1 switches= OFF and switch 3 of SW2= OFF:

nevertheless some working parameters can be modifyed

using internal dip-switches.

DIP-SWITCH #1 (on board M416.x: see position on next

page): allows to override some external alarms, as follow

SW1-1 if set to ON disables ARC DETECTOR alarm.

SW1-2 if set to ON disables MAGNETRON THERMAL

alarm

SW1-3 if set to ON disables AIR FLOW alarm

SW1-4 if set to ON disables WATER FLOW alarm

SW1-5 if set to ON disables HEAD ENABLE

SW1-6 if set to ON disables microswitch CARTER alarm

SW1-7 if set to ON inhibits the automatic opening of the

interlock relay from the CPU in case of alarm. If it is ON,

only the opening of the MICRO CARTER switch can de-

energize

the interlock relay, cutting in this way the head supply and

leaving the head in a safe condition.

SW1-8 – not used.

DIP-SWITCH #2 (on board M416.x)

SW2-1: not used

SW2-2: not used

SW2-3 if set to OFF enables the external control of the

unit, set to ON enables the fieldbus control.

The default setting for SM1690x is OFF.

WARNING: in ON state, if no fieldbus interface is

present or if no communication is present on the bus,

an alarm is generated.

SW2-4

must be set to OFF for normal

operation

, if set to ON enables the

hardware test of the M416 board.

WARNING:

don’t enable

this switch: the

use is limited to

trained personal

only and for test

purposes.

CPU POWER

HEAD INTERFACE POWER

PLC INTERFACE POWERING

HEAD INTERFACE (CONN#2)

HEAD POWER OUT (CONN#4)

230Vac BOARD POWER

LED BOARD

FIELDBUS INTERFACE

RS232 INTERFACE

M416.1 CONNECTORS, TEST-POINTS, LEDS

TRIMMERS, DIP-SWITCHES, JUMPERS

DIP-SWITCH#2

DIP-SWITCH#1

FILAMENT VOLTAGE ADJ.

PTC ON HEATSINK

FAN POWER

DRIVER COMMAND

PARAMETERS SENSING

CONTROL I/O (CONN#5)

id32384187 pdfMachine by Broadgun Software - a great PDF writer! - a great PDF creator! - http://www.pdfmachine.com http://www.broadgun.com

Содержание SM1690 Series





















Результаты поиска

Содержание SM1690 Series

Отзывы:

Похожие инструкции для SM1690 Series

Бренды по названию

Популярные бренды

MKS SM1690 Series, Технические заметки

Результаты поиска

Содержание SM1690 Series

Отзывы:

Похожие инструкции для SM1690 Series

Бренды по названию

Популярные бренды