MKS Newport CONEX-LDS Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 28

background image

CONEX-LDS

Controller GUI Manual

Start performance verification Button

Opens a user-friendly interface to validate the CONEX-LDS calibration. The label on

the button changes to “Stop” to cancel the current calibration verification process.

•

Error

≤

3%

=

GREEN

indicator, OK

•

Error >

3%

=

RED

indicator, consider sending the CONEX-LDS to the factory for

calibration

REFERENCE INFORMATION

The optical wedge of the CONEX-LDS-VER calibration verification kit induces

an angular deviation to the autocollimator's beam. This deviation corresponds to

a measurement angle of approximately 1000 µrad. The exact angle is measured

and reported in the Calibration Certificate shipped with each CONEX-LDS-

VER Kit. The user should input KitSerialNumber and ReferenceAngleValue

from the Calibration Certificate in the Configuration tab. The verification

process consists of 4 measurements, spaced 90° apart on the PSD. These

measurements are compared to the CONEX-LDS-VER reference angle set by the

user in the Configuration tab. Before performing this verification and inserting

the optical wedge, the mirror must be centered so the CONEX-LDS reads X = 0

and Y = 0 ±10 µrad.

11

EDH0331En1032 — 12/18

«
...
13
14
15
16
17
...
»

Содержание Newport CONEX-LDS





























Отзывы:

Нет отзывов

Похожие инструкции для Newport CONEX-LDS

Бренд: GE Страницы: 242

Бренд: GE Страницы: 24

Бренд: Balanced Body Страницы: 3

Бренд: Ecco Страницы: 9

Бренд: Talet Equipment Страницы: 17

Бренд: Barreto Страницы: 20

Бренд: Barreto Страницы: 18

Бренд: Backyard Discovery Страницы: 41

Бренд: Hach Страницы: 66

Бренд: Hach Страницы: 14

Бренд: Hach Страницы: 144

QuikChem 8500 2 Series

Бренд: Hach Страницы: 80

Бренд: Hach Страницы: 178

Бренд: Hach Страницы: 32

Бренд: hager Страницы: 4

Бренд: Jet Страницы: 12

Бренд: Yamaha Страницы: 48

Бренд: YOKOGAWA Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды