background image

                                                                                                                                             

11

                                                                    

EDH0387En1020 — 09/18

BG Series                                                                                                                  Goniometric Cradles

5.0  —

Connection to Newport Controllers

5.1

Warnings on Controllers

Controllers are intended for use by qualified personnel who recognize

shock hazards and are familiar with safety precautions required to avoid

possible injury. Read the controller user’s manual carefully before

operating the instrument and pay attention to all written warnings and

cautions.

WARNING

Disconnect the power plug under the following circumstances:

• If the power cord or any attached cables are frayed or damaged in

any way.

• If the power plug is damaged in any way.

• If the unit is exposed to rain, excessive moisture, or liquids are spilled

on the unit.

• If the unit has been dropped or the case is damaged.

• If you suspect service or repair is required.

• Whenever you clean the electronics unit.

CAUTION

To protect the unit from damage, be sure to:

• Keep all air vents free of dirt and dust.

• Keep all liquids away from the unit.

• Do not expose the unit to excessive moisture (85% humidity).

• Read this manual before using the unit for the first time.

WARNING

All attachment plug receptacles in the vicinity of this unit are to be of
the grounding type and properly polarized.

Contact your electrician to check your receptacles.

WARNING

This product is equipped with a 3-wire grounding type plug.

Any interruption of the grounding connection can create an electric
shock hazard.

If you are unable to insert the plug into your wall plug receptacle,
contact your electrician to perform the necessary alterations to ensure
that the green (green-yellow) wire is attached to earth ground.

WARNING

This product operates with voltages that can be lethal.

Pushing objects of any kind into cabinet slots or holes, or spilling any
liquid on the product, may touch hazardous voltage points or short out
parts.

Содержание BGM120































Отзывы: