MK MK-2013HE GX390 Скачать руководство пользователя страница 10

Страница: 10 / 60

oPERATIoN & SAFETY dECAlS

Part # 164202

WARNING

• This equipment may produce dust or mists containing

crystalline silica.

• Silica is a basic component of masonry, concrete, and

other materials.

• Repeated and/or substantial inhalation can cause

serious or fatal respiratory diseases including silicosis.

• Respirable crystalline silica is listed by California and

other authorities as a substance known to cause cancer.

• Employ dust controls and protection per

OSHA/NIOSH/MSHA.

Part # 155587 (3)

CAUTION

DO NOT

operate without

guards in place.

Part # 155588

Part # 154398

WARNING

In the event of blade

failure, replace

blade guard

immediately.

DO NOT operate

this equipment

before reading the

owner’s manual.

WARNING

Part # 155038

SERVICE OR

WARRANTY

FOR INFORMATION ON

PLEASE CALL

1-800-474-5594

Part # 170480

Part # 155585

CAUTION

Keep

hands and

feet clear.

Part # 154399

NOTICE

Overtensioning of belts will

result in premature crank

and/or bearing failure.

Part # 155582

Part # 156749

Part # 155579

CAUTION

DO NOT

touch hot

surface.

Part # 155578

CAUTION

Accidental start hazard.

Disconnect spark plug prior

to servicing.

Part # 155580

Part # 155581

WARNING

When refueling

stop engine and

allow to cool.

DO NOT

overfill tank.

DANGER

The exhaust from this product con-

tains chemicals known to the State

of California to cause cancer, birth

defects or other reproductive harm.

DANGER

Lethal exhaust

gases. Use only

in well ventilated

areas. DO NOT

use indoors.

location

description

Gas Tank - Top

Warning - Silica

Frame - Side

Read Manual

Shaft Cover/Belt Guard/Blade Guard Guards in Place

Blade Guard - Top

Replace Blade Guard

Console

Service

Frame - Front

Hand & Feet Clear

Belt Guard - Front

Overtensioning Belts

Gas Tank - Side

Refueling

Belt Guard

Hot Surface

Belt Guard

Accidental Start

Gas Tank - Side

Exhaust/Cancer

Console

QR Code for Manuals

Gas Tank - Side

Lethal Exhaust

Console

Machinery Hazard

MK-20 SERIES SAFETY

The MK-20 Series Concrete Saw is equipped with a number of safety decals. These decals are pro-

vided for operator safety and maintenance information. Should any of these operation or safety de-

cals become unreadable, replacements can be obtained by calling (

800) 262-1575

C
G

location of Safety decals for models:

MK-2013HE, MK-2013HSP, MK-2013SE,

MK-2013SSP, MK-2013VSP, and MK-2014K

Содержание MK-2013HE GX390





























































Результаты поиска

Содержание MK-2013HE GX390

Отзывы:

Похожие инструкции для MK-2013HE GX390

Бренды по названию

Популярные бренды

MK MK-2013HE GX390, Руководство пользователя и инструкции по эксплуатации

Результаты поиска

Содержание MK-2013HE GX390

Отзывы:

Похожие инструкции для MK-2013HE GX390

Бренды по названию

Популярные бренды