MK Diamond Products MK-2013 HE Скачать руководство пользователя страница 3

MK-20 SERIES

Revision 09/06, Effective Date September 18, 2006

3

(

(

)

)

on

Never tamper with the governor components or settings to increase the maximum speed. Severe personal injury and damage to the 

engine or equipment can result if operated at speeds above maximum.

Adhere to safety guidelines: ANSI American National Standards Institute, OHSA, or local Regulations. Never operate the saw with out 

the guards in place!

Before using this equipment, ensure that the person operating this machine has read and understands all of the instructions in the 

manual. Precaution is the best insurance against accidents. Read and understand all safety precautions, messages, warnings and 

hazard symbols. You are responsible for your own safety.

(

(

)

)

on

(

(

)

)

on

(

(

)

)

on

(

(

)

)

on

Read Owner‘s Manual Before Use!

Keep Gaurds In Place!

Over Speed!

hazard symbols

You CAN be KILLED or  SERIOUSLY injured if you don’t follow instructions.

You CAN be injured if you don’t follow instructions.

(

(

)

)

on

Caution

Danger

Engine components can get extremely hot from operation. To prevent severe burns, do not touch these areas while the engine is 

running or immediately after it is turned off. Never operate the engine with heat shields or guards removed.

(

(

)

)

on

Hot Parts!

Gasoline is extremely flammable and its vapors can explode if ignited. Store gasoline only in approved containers, in well-ventilated, 

unoccupied buildings, away from sparks or flames. Do not fill the fuel tank while the engine is hot or running, since spilled fuel could 

ignite if it comes in contact with hot parts or sparks from ignition. Do not start the engine near spilled fuel. Never use gasoline as a 

cleaning agent.

(

(

)

)

on

Explosive Fuel!

Additional information as to the nature of the hazard is provided by the following hazards symbols which appear throughout the 

manual in conjunction with safety message alert symbols.

Never touch electrical wires or components while the engine is running. They can be sources of electrical shock which could cause 

severe injury or burns. 

(

(

)

)

on

Electrical Shock!

Before servicing the engine or equipment, always remove the key and disconnect the spark plug lead to prevent the engine from 

starting accidentally. Ground the lead to prevent sparks that could cause fires. Make sure the equipment is in neutral.

Engine exhaust gases contain poisonous carbon monoxide. Carbon monoxide is odorless, colorless, and can cause death if inhaled. 

Avoid inhaling exhaust fumes, and never run the engine in a closed building or confined area.

Keep hands, feet, hair, and clothing away from all moving parts to prevent injury. Never operate the engine with covers, shrouds, or 

guards removed.

(

(

)

)

on

(

(

)

)

on

(

(

)

)

on

(

(

)

)

on

Accidental Starts!

Rotating Parts!

Lethal Exhaust Gases!

Always use approved eye protection with side shields or face shields.

(

(

)

)

on

(

(

)

)

on

Use Approved Eye Protection!

(

(

)

)

on

Warning

safety messages

A safety message informs you about potential hazards that could hurt you or others. Each safety message is preceded by one of the 

three words: Danger, Warning, or Caution.

Содержание MK-2013 HE











































Отзывы: