MK Diamond Products MK-101-24HD Скачать руководство пользователя страница 59

Страница: 59 / 60

MK-101-24HD

CONTACT & WARRANTY

CONTACT:

Please contact MK Diamond Products, Inc. Customer Service Department with any questions you

might have regarding distributors, parts or service.

Telephone: (800) 421-5830

Fax: (310) 539-5158

E-mail: [email protected]

Customer Service Hours: Monday through Friday, 6aM-4PM PSt

MK Diamond Products, Inc.

1315 Storm Parkway

Torrance, CA 90501

The MK Diamond logo is a registered trademark of MK Diamond Products, Inc. and may not be used,

reproduced, or altered without written permission. All other trademarks are the property of their re-

spective owners and used with permission.

MK Diamond may have patents, patent applications, trade marks, copyrights of other intellectual

property right covering this product in this document.

This manual MUST accompany the equipment at all times. This manual is considered a permanent

part of the equipment and should remain with the unit if resold.

The information and specifications included in this publication were in effect at the time of approval for

printing.

MK DIAMOND PRODUCTS, INC. will guarantee every machine they build, to be free from defects in

material and workmanship for (1) one year from date of purchase. The obligation of MK DIAMOND

PRODUCTS, INC. under this warranty is limited to the repair or replacement of any parts which,

under normal use, prove to be defective in material or workmanship. The parts involved or the unit

in question should be returned to MK DIAMOND PRODUCTS, INC. or to a point designated by us,

transportation prepaid.

This warranty does not obligate us to bear the cost of labor or transportation charges in connection

with replacement or repair of defective parts. Likewise, it shall NOT apply to any unit which has been

subjected to misuse, neglect or accident. This warranty does NOT apply to any machine which has

been repaired or altered outside our factory.

This warranty does NOT obligate MK DIAMOND PRODUCTS, INC., with respect to items not of our

manufacture, such as engines, motors, hydraulics, etc., which are subject to their own guarantees and

warranties.

We shall in no event be liable for consequential damages or contingent liabilities arising out of failure

of any equipment or parts to operate properly.

MK DIAMOND PRODUCTS, INC. LIMITED WARRANTY

Содержание MK-101-24HD





























































Результаты поиска

Содержание MK-101-24HD

Отзывы:

Бренды по названию

Популярные бренды

MK Diamond Products MK-101-24HD, Руководство пользователя и инструкции по эксплуатации

Результаты поиска

Содержание MK-101-24HD

Отзывы:

Бренды по названию

Популярные бренды