manualshive.com logo in svg

MK Diamond Products MK-101-24HD, Руководство пользователя и инструкции по эксплуатации

Поделиться
Скачать
MK Diamond Products MK-101-24HD Скачать руководство пользователя страница 44

44

(A)

Remove the Cooling Transfer

Tube from the Blade Guard 

inlet. Go to Step C.

(B)

Place Pump into a bucket of 

water and check flow. If flow 

exists, go to Step D.

(C)

Remove the Cooling Transfer

Tube and check for flow. If flow 

exists, refer to water pump 

manual.

(D)

Remove the Blade Guard

Intake Fitting. Go to Step F.

(E)

Remove the Cooling Channel

cover screws. Go to step G.

(F)

Rod the Cooling Channels

and then recheck flow.

“Rodding” cooling channels is performed by inserting a small wire rod through the 

cooling inlet on top of the Blade Guard and directing the rod out through each of the 

cooling flow tubes located on the underside of the Blade Guard.  The cooling chan-

nels should be “rodded” until all ports are free of foreign debris.

MK-101-24HD   

TROUBLESHOOTING

Cooling Flow

NOTE:

Содержание MK-101-24HD





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды