manualshive.com logo in svg

MK Diamond Products 159345, Руководство пользователя

Поделиться
Скачать
MK Diamond Products 159345 Скачать руководство пользователя страница 10

10

OPERATION & SAFETY DECALS

CX-3

®

                                                                                                             SAFETY

The CX-3

®

 Concrete Saw is equipped with a number of safety decals. These decals are provided for 

operator safety and maintenance information. Should any of these operation or safety decals become 

unreadable, replacements can be obtained by calling (800) 262-1575.

Decal/Label Location

Description

A

Cross Bar

Warning - Dust Control

B

Console

Warning - Silica Prop 65

C

Blade/Belt Guard/Shaft Cover

Caution - Guards in Place

D

Console

Warning - Read Owner’s Manual

E

Gas Tank/Top

QR Codes for Manuals and Safety

•  This Equipment may produce Dust 

or Mists containing Crystalline Silica. 

•  Employ Dust Controls and Protection 

per OSHA/NIOSH/MSHA.

WARNING

!

Label #164202

Part # 164202

A

Part # 170480

Scan for safety information

Scan for manuals

Label #170480

E

Part # 154398

DO NOT operate 

this equipment 

before reading the 

owner’s manuals. 

WARNING

!

Label #154398

D

B

!

       WARNING: 

This equipment contains chemicals known to 

the State of California to cause cancer and birth defects or other 

reproductive harm. These chemicals are contained in various 

components, fluids and paint, including but not limited to, fuel, oil, 

electric motors and batteries. In addition, gasoline/diesel powered 

equipment emits engine exhaust and fumes, and when serviced, 

cleaned or maintained generate used oil, waste fluids, fumes, 

grease, grime and particulates from component wear and silica 

dust which contain chemicals known to the State of California to 

cause cancer and birth defects or other reproductive harm.
For more information go to 

www.P65Warnings.ca.gov.

Label #172641

Part #172641

Part # 155587

CAUTION

DO NOT

operate without 

guards in place. 

!

Label #155587

C

Содержание 159345





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды