Mitsubishi QD62-H01 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 18

Mitsubishi QD62-H01 Скачать руководство пользователя страница 12

6

5. External Wiring

5.1 Wiring Precautions

1) Different terminals have been prepared for connection depending on the

voltage of the input signal. Connecting a terminal of incorrect voltage may
result in malfunction or mechanical failure.

2) For 1-phase input, always perform pulse input wiring on the Phase A side.
3) When pulse status noise is input, the QD62-H01/H02 may miscount.
4) Provide the following measures against noise for high-speed pulse input:

a) Always use a shielded twisted pair cable and provide grounding.
b) Avoid placing the shielded twisted pair cable parallel to wires that have

large amounts of noise such as power cables or input/output cables.
Place the cable at least 150mm (5.9 inch) from such wires and perform
wiring using the least distance as possible.

5) An example of wiring incorporating measures against noise is shown

below:

Terminal block

Programmable

controller

Provide a clearance

of 150 mm (5.9 inch)

or more from I/O

wires to high voltage

equipment such as

inverters. (Also

exercise caution for

wiring inside the

panel.)

AC

motor

Relay box

QD62-H01/H02

Carrier

Do not enclose solenoids and inductive loads together within the same metal conduit.
If a sufficient distance cannot be secured to isolate ducts and other wires from a high-
voltage line, use CVVS or other shielded wire for the high-voltage line.

Encoder

Inverter

The distance between the encoder and relay box
must be short. Allowing a long distance between
the QD62-H01/H02 and the encoder may cause a
voltage-drop problem. Using a tester or other
measuring device, confirm that the voltage at the
terminal block of the relay box doesn't exceed the
rated voltage when the encoder is in operation or
at standstill. If a substantial voltage drop occurs,
increase the wire size or use a 24 V DC encoder
with minimal current consumption.

• Grounding the shielded twisted pair cable is performed on the encoder side (relay box). (This example shows

connection with 24 V sink load.

To A

To QD62-H01/H02

Current for the encoder

24V

E

+ 24 V

0 V

E

The shielded wire for the encoder and shielded
twisted pair cable are connected inside the relay box .
If the shielded wire for the encoder is not grounded
inside the encoder, ground it in the relay box, as
indicated by the dotted line.

To the encoder

To B

A
B

«
...
10
11
12
13
14
...
»

Содержание QD62-H01



















Отзывы:

Нет отзывов